This door handle for your washer is sold without screws, they can be ordered separately, or you can reuse the existing screws if they are in good shape. To replace this part, simply unscrew the handle and screw the new one into place.
This washer drain pump is a genuine replacement component designed for select front-load washing machines from Whirlpool, Maytag, Kenmore, and affiliated brands. It plays a vital role in the wash cycle by efficiently removing water from the drum, helping to prevent leaks and ensure proper drainage. A malfunctioning pump may result in slow...Read more or incomplete draining, water leakage, or error codes related to pump failure. This part is engineered for durability and reliable performance, and replacing it can restore optimal function to your appliance. Compatibility should be confirmed using your washer’s model number prior to installation.
This washer door lock and switch assembly is a critical safety and control component for front-loading washing machines. It secures the door during wash and spin cycles, preventing accidental opening and ensuring the appliance operates only when properly latched. The integrated interlock switch communicates with the washer’s control syste...Read morem to verify door status, helping prevent cycle interruptions and operational errors. This model features a four-lead switch for precise functionality and is compatible with a wide range of front-load washers. Replacing this part can resolve issues such as a door that won’t close, won’t open, or won’t lock, as well as a washer that fails to start. Installation should be performed with the appliance unplugged and may require basic tools.
Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dave - For model number GHW9100LW1
January 4, 2020
Whirlpool duet what is the cubic foot capacity of this older model? Thank you.
Hello Dave and thank you for writing.
The unit is 3.7 CuFt. We hope this helps. Please contact us anytime if you require further assistance.
5 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Clint - For model number GHW9100LW1
January 25, 2020
What it the capacity of the Whirlpool duet ghw9100lw1 washer?
Hello and thank you for writing.
This unit is 4.1 cubic feet. We hope this helps. Please contact us anytime if you require further assistance.
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Ian - For model number GHW9100LW1
February 13, 2020
I push controller on button lights are flashing red then push start button nothing happens red flashing light on all loads
Hi Ian, thank you for your question. It sounds like you might need to reset your appliance. To do this you should unplug your appliance for about 30 minutes. Once you plug it back in, press and hold the End of Cycle/Cycle Signal button for 20 seconds. This should fully reset your board and the light should stop. If the issue continues then you may need to check your door lock and the electronic control board for being the issue. Good luck with your repair.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Mike - For model number GHW9100LW1
February 22, 2020
When on spin cycle the basket starts banging like it is hitting the enclosure and the faster it spins the louder it gets
Hello Mike,
Thank you for your question We have done an investigation into your model GHW9100LW1, we have discovered that the Shock Absorber would be the most accurate cause of your symptoms. It is available under part number PS11745030. If the shock absorber is malfunctioning, it can cause the drum to be misaligned during the spin cycle and will cause various levels of noise. We hope this helps you.
Hello Wayne,
Thank you for your question. You will need to access the back of the washer by either pulling the tub out through the front, or accessing the motor and clutch through the back of the washer. We hope this helps.
Was this helpful?
Thank you for voting!
Prev
1
2
3
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken plastic washer door handle
541 of 550 peoplefound this instruction helpful.
dave from woodway, WA
Really Easy
Less than 15 mins
Screw drivers
Just required removal of two screws, placing the new handle and reinstalling the two screws. Easiest repair I've ever done!
Was this helpful?
Thank you for voting!
Washer would not drain ,F02 and SUD code displaying
237 of 253 peoplefound this instruction helpful.
Donald from Wichita, KS
A Bit Difficult
1- 2 hours
Pliers, Socket set
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door. (3) I packed towels under the washer. (4) I slowly removed the cleanout i
... Read moren the front of the pump, using the water vac to catch the water as it leaked out. (5) I removed the wiring to the motor. (6) I removed the screw that holds the pump in place with a Torx T-20 socket. (7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ). (8) I tested the pump and found it would run but was making a lot of noise and running slow. (9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4). Don Kramer Wichita, Kansas
Read less
Was this helpful?
Thank you for voting!
front load washer latch replacement
198 of 242 peoplefound this instruction helpful.
James from Vilonia, AR
A Bit Difficult
Less than 15 mins
Nutdriver, Screw drivers
1. remove the three screws from the top backside of the top panel 2. push the top panel to the rear 1/8 to 1/4 inch 3. lift/rotate top panel from rear to front, set aside. 4. remove the three wire connectors from latch. 5. use #15 Torx to remove the three screws from the latch. 6. remove and replace part using to
... Read morep opening. 7. reverse order to finish.
My Orders
