GFMN110GD0WW General Electric Dryer - Instructions

Good thing my husband is so handy. This part was very difficult to get to. Basically, he had to take apart almost the whole dryer. There is no access door so the side panel had to be removed, but before you could do that the front panel and door had to come off, then the top of the dryer. Keep track of the screws, we had a few leftover! But the dryer works great again and we hope to get several more years out of it. We've had no problems with it until now and it's over 15 yrs. old.

Well, the intall would have been great except for the fact that I needed another part. If your belt breaks there is a reason for it. Make sure you check all the parts that work with the belt. Their was a pully the was defective and also need to be replaces. I think it would be a good idea to put a little note on the page for the Belt Drive to let people know that if you are replaceing the belt you might want to check the Idler Pully for it too might need to be replaces. I'm not an expert and if that was on the page for the Belt Drive I might have look at the pully before I ordered and I would have ordered the part along with the Belt Drive. As it was had to wait another 4 day to get my dryer fixed. I'm very happy the Parts Select has all my parts and they pretty good at getting them out to me in a good amount of time when I need them.

Screwed the light bulb into the socket (duh)

Un plug the dryer. Gather phillip, flat head and torix screw drivers. Remove the rear of the dryer to get the spec sheet with the appropriate part number. Next called for part. Belt installation requires removal of front and top of dryer in order to slide belt over the drum. Getting to all the fastners requires tilting the dryer on its back. Clean out excess lint from dryer interior and duct work. Slide drive belt over drum and use some masking tape to hold it in position. Reassemble dyer. Return dryer to upright position and put the belt on the pully and tensioner from rear access port. Remove tape. Replace access panel. Reattach vent duct work. Plug in. There are 5-6 different size screws holding everything together...you may want to use masking tape to label where each type of screw goes. All totaled it took about an hour and cost less that $25. Well worth the effort.

All the stores had either a smaller watt or a larger watt and the book suggested always using the correct watt. I was glad to find it on this sight and it was delivered very quickly.

I removed the front cover and top of the dryer by removing screws visible from opening the dryer door. I then had to figure out exactly how the belt was set around the drum and other pulleys. With the belt around the drum and around the motor rotor, the other pulley had to be very forcibly pushed towards the drum in order to get the belt seated correctly. This being my first dryer repair, I was unsure of how the belt was needed to placed. But eventually figured it out using pictures from the internet. The second pulley required a lot of force and I had to squeeze my hand and arm under the drum of the dryer in order to make the belt fit correctly with enough slack to reach around the second pulley.

Open up the unit's lid first and then removed the front panel. Then I removed the broken belt and then routed the new belt around drum, through the belt tensioner, and onto to the motor pulley. I checked to make sure the belt was securely in place and if it would rotate the drum. Once I was positive it was in place I put the dryer panels back together, plug in the dryer, and tested operation. The only thing that was difficult was trying to figure out the routing of the belt through the tensioner because the old belt wasn't in place anymore. In all it was a 45 minute job.

removed two phillips screws from front panel, removed front panel and raised top cover, had my wife hold up top cover while i removed belt and installed new one, reassembled in reverse order, turned on dryer and checked for proper operation, and yes i did unplug the unit. worked great!!

I removed the two screws inside the door and popped the top loose. I took the top off to see and have access to the interior. I leaned the front out and inserted the belt around the drum (with my wife's help), replaced the screws and laid the dryer on it's face on a rolled up blanket and proceeded to run the belt around the pulleys (two). The drive pulley was easy but the idler pulley, not so easy. I had to figure out how the pulley arm was supposed to provide tension on the belt. I figured it out by looking at the diagram. It was then I found the idler pulley was broken and fell apart in my hand. I advise that a new pulley be installed at the same time as the belt. Everything I read on your web site helped.

no problem open top remove front install new belt

Removed the top of the dryer 2 screws. procedure
open dryer door. At the top of the dryer door their is
two screws left to right, Remove them and lift top
off. Inside where the top was is two screws left to
right. Remove the two screws and take the front
panel off. Carefull not to pull wireing loose. Lean door against something so you don't have to disasemble wireing. Pull broken belt out and install new belt around tumbler and up and over
tension pulley and pull down and slip over the motor pulley. Your'e done. Reassemble front then
top. My dryer ran just fine after these steps. The question and answers helped me do this.

This is a space saver one piece unit with dryer on top. I first removed ten screws that hold the top on, I then removed four more screws that hold the front service cover on and two last screws that hold the rear service cover on. Now I seperated the front cover of the dryer from the dryer tumbler tub and slipped the new belt around the tub, then at the rear service cover I feed the belt through the tensioner and back onto the motor pully. Now just put the covers back in reverse order of removal and all done! "Piece of cake"
Ron

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.

Dryer would turn on when you pushed the "on" button, but as soon as you let go, it would turn off. Found the plastic door switch cracked (from slamming door closed). Unplugged the dryer. Unscrewed the two screws inside the top of the door to unfasten the top panel. Took the top panel off. Then unscrewed the two screws on the side to unlatch the front panel. Used plyers to take the 3 wires off the switch and slid the switch through the front of the door. Juat remember where the wires go. Then inserted new switch and connected the wires. Vacuumed out the dryer and reassembled. It took about 20 minutes and was easy! If I can do it, you can!!!

It took a while to diagnose the problem. I finally figured out it was the door switch by pushing it with my finger with the dryer door open and starting the dryer. It would run like that, but the switch was not being pressed in enough by the door. I ordered the switch and I should have been able to replace in about 15 min. But the old switch broke while I was removing it and it fell back inside the unit. So I had to remove the top and the front panel to access the door switch. That's why it took so long. If that had not happened it would have been a much simpler repair.