GFE24JBLLFTS General Electric Refrigerator - Instructions

Very easy and the part was a perfect fit

I Googled how to fix a ge door handle. It was super easy. Just slide it up, take it off and replace by putting the new one in place and sliding down till it clicks.

Just placed the shelf on the door

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

Removed and replaced correct item received however one was cracked right out of undamaged properly packed box submitted claim and refund quickly processed by the seller recommend inspect upon receipt.

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Installing the part repaired the fridge and freezer immediately.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

I ordered the 3 shelves from Parts Select requiring replacement based on the GNE25JGKFFWW Parts By Section diagram (parts 540, 541 & 542) and the removals and installations were very simple, no tools required but major issue was shelf 540 for left side of the refrigerator did not fit. Parts Select sent me the same wrong shelf 3 times and all were returned. Last conversation with Part Select rep they gave me the number to General Electric because they finally figured it out the the shelf (540) depicted on their website did not fit our refrigerator. I've purchased items from Parts Select before but sending the wrong part to us on 3 separate occasions was concerning

removed 6 screws and repaced cover.

The handle was already broken. Wish I would have checked the mating clip surface of the handle. But, after getting all set up saw this problem, and ordered a handle. Taking off and installing is simple. Tap the freezer handle end to the left using a soft mallet on the right end. I suspect a hammer would work, but without protecting the handle could bend it or at least scratch the paint. I suppose a folded rag and a hammer may work. Anyway, once off, replacing the clips on the door is a Phillips head screwdriver to unscrew and replace the door clips. Then, carefully tapped the handle from the left end to slide the mating piece in the handle back on and tap tightly. There were many YouTubes on the thing since it seems to me to be a very poor design. But maybe we are too hard on the handle???

Pulled the fridge out. Removed the back panel over the mother board. Removed and replaced. Easy peasy and working well.

Replaced Temperature Sensor and now it is getting cold.

Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.

Removed ice bucket, and unplugged ice maker. Removed light cover. Removed ice maker. Pulled fan blades straight up and removed. Pushed new blades on to motor shaft. Fairly easy .