Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Noisy squeaking drum...
I replaced the drum bearing slides and also the main front drum bearing. First, disconnect the electric. Then I removed the two screws inside the door that attach the top cover, removed the top cover, removed two screws that attach the front cover, lift up the front cover and pivot it to the left leaving the wiring attached, removed the front bearing assembly by pulling it out at the top and then up, installed the new front bearing ring and snap it into place, installed the drum bearing slides, reinstalled the front cover, reinstalled the top cover, and tested the drum by turning it by hand first and then under power. The whole operation took less than 15 minutes....
Dryer was catching clothes and would not release without very hard pulling, consequently twisted and grease marked fabric, ruining items.
I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!
When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.
Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job
My dryer was making a really loud, high pitched squeak and eventually a grinding noise
I order the parts needed to replace the slides, the felt ,and the bearing on a Sunday afternoon. The parts arrived on Tuesday even though I used regular shipping. I followed the instructions posted by another customer. It was extremely easy and only took me about fifteen minutes. My only problem was that I needed 2 each of the front slide and the rear slide, and I unknowingly only ordered 1 of each. I order the other 2 on Tuesday via regular shipping and they arrived on Wed. AMAZING!!!!
Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.
First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.
I removed the top cover and the back cover to install new belt. Once i put new belt i discovered that the pulley was also broken so now i have order the pulley so that i can complete the repair
evidently the pulley spring on video was very very very weak
the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.