GDWT668V55SS General Electric Dishwasher - Instructions

Middle arm bearing used a pair of pliers to unscrew the screw and to re-screw with new bearing in place. NO did not have to disconnect the arm. Lower arm turn counter clockwise to remove (comes off very easy) stick needle nose straight down opening and remove bearing. Use needle nose to place new bearing.

Installed new rack assembly and it works fine. Thanks

removed original rack, inserted replacement.

Simply took out the broken rack and inserted the new one.

I took the old one out and replaced it with the new one. It did take both hands as I had to open the dishwasher door while the other hand held the basket. :D

opened the dishwasher .............removed the old and slid in the new ...then attached by dropping in the utensil compartment.....piece of cake

My husband followed the directions included with the replacement part that we ordered. It was so great to read of others' experience installing the part! It works great and we will certainly use this site again. Thank you so much. We saved $100.00 doing it ourselves.

After reading other customer responses I decided to attempt the repair myself. After pulling out dishwasher I turned it on it's side and prodeeded to remove the 3 screws holding it in place. FIFTEEN minutes later I pushed it back into position and it has performed like new for the past month. Comparing parts and service I saved about $200.00 on this self repair. I would not hesitate to undertake another repair after my experience.

Remove the door panel screws on the inside door frame. You only need to remove as many as needed to remove the larger bottom panel. The other screws will remove the upper button panel and this is not necassary. Unplug the Detergent Dispenser (it may take some force, and unscrew the dispencer. Replace with the new one, screw back in place, and reattatch the plug. Now replace the door panel and screw it back in place. This is all very simple. The only problem I encountered was that the only dispenser had built up so much detergent residue around its base, that it had distorted the plastic around it. This caused the new dispense to not sit flush all the way around, and the dishwasher leaked into the door on its first cycle. Simply filling the gap with 100% silicon caulk has fixed the problem. Washes like new.

we followed the instructions as posted on your web site. Once the dishwasher was apart it was self explanatory. We did however need pliers to separate the wires from the old soap dispenser.

Open the door and go along entire edge of door and use Philipps to unscrew the front panel of the door from the inside panel of the door. Once unscrewed open carefully. There are screws in the dispenser cup. Undo those and then there are two plugs to be undone. There is also the main black computer component that has to be unplugged from its cord. Just remove and screw everything back the way it was. This was my first time and I am a female age 58 years old. It was simple. If I had to do it again I could do it in less than half the time.

Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.

Remove door cover shell by removing screws in inside of door. Unplug harness to control module.Remove outer door shell.Remove four screws at the blower motor. Replace with new motor after disconnecting harness to motor. Reinstall module harness reinstall door shell.

Removed the door gasket and cleaned the track prior to installing the new gasket. The online repair instructions didn't mention a thin wire that is stored at the bottom of the tub near the door and is used to hold the ends of the gasket in place. Gently remove the ends of the gasket from the wire prior to pulling the entire gasket out of the machine track.

We noticed our detergent door was not opening on cue to dispense the soap and it was leaving our dishes dirty. It came to be that our spring was sprung on the detergent door. I researched it and I could either buy the spring or the whole detergent contraption (installing the contraption was one wrench easier but cost $35 more). Knowing my husband the way I do, I decided to do the more costly route. I followed the instructions from previous installers on here and me and my husband did it in 30 minutes! I do agree that it is a two man job for some of it as I stressed to him NOT to take the front off haphazardly, as it was $400 to replace that! We took the 12 or so screws off, detached the line to the detergent dispenser, reattached, screwed it into the door and replaced the front 12 or so screws again. Easy peasy! Unbelieveable!