GDF650SSJ0SS General Electric Dishwasher - Instructions

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

I follow a YouTuber who had a semillar GE dishwasher model number. He was very helpful through the repair process.

Followed video instructions and all went went well.

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

just bolted on the new one and hooked up the hose

Took old valve assembly off and replaced with new assenbly

The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break.

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

Dishwasher is under 2yrs old and suddenly failed to drain due to the drain pump not working. I read the reviews on how easy it was to change and went ahead and purchased one. After removing the screw from the appliance bracket under the counter and the two screws from the base plate, it was easy to pull the dishwasher from under the counter and away to flip to its side. I would recommend draining the drain hose first and making sure no water is in the tub. Keep a towel nearby. Removing the drain pump was simple. I needed a nose tip pliers to remove one of the hose clamps and a screwdriver for the other clamp. Once the pump was removed, I opened the old pump by twisting the top part while pressing the tabs to remove upper housing. There was a broken piece of glass that had wedged itself in the mechanism which prevented the pump from working. I wish I had checked that first, before purchasing a new drain pump. I kept the old pump as a backup for the future. It took no more than 20 minutes to get the pump replaced and the dishwasher back in place. Dishwasher drains just as new. By the way, costed under $100 with delivery. An appliance repair company wanted $250!!
Not the first time PartSelect saved me money and won’t be my last!

This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher

Shut off power to the unit, removed the front lower trim and under counter screws, then I disconnected the wiring from under the door leading to the UI at the top edge of the door. Removed the front door, separated and disassembled the outer door cover, I then removed the UI control board from its housing and the clear cover and reassembled the parts in reverse order and turned the power back on. FOLLOW the included instructions on connecting the pins on the new UI by cross reference the model number.

The repair went very well, I watched a video on how to fix it on utube for this model the board from partselect was a OEM and fit perfectly. If I ever have an appliance problem partselct will be the number 1 on my list to call. I have told most of my friends about them and how great they are to deal with. They rate eleven stars.