GDF520PSD0SS General Electric Dishwasher - Instructions

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute

A quick twist of the locking nut

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.

Replaced latch

Shut Power off at Circuit Breaker
1. Remove Kick Plate & Insulation
2. Unplug electrical connection from door to unit
2. Remove 2 screws with nut driver to release panel above electrical connection box
3. Pull panel down and out to expose board
4. Disconnect 3 plugged wire leads
5. replace old board with the new in the tray
6. Plug connectors in
7. Put unit back together

The main board is located under the washer in metal box accessed by removal of front plate at bottom. Removal of 2 screws on front of metal box allows board to drop down. However, very cumbersome to work on your back on floor in small space. I took the easy way and slid the washer out of cabinet, then turned washer ( it's light weight) on its back to access & remove old board and easily replace with new one. Also one of the connector plugs had to be replaced wired into the power connection made me very glad I was not working on my back ! Then simply turn washer upright and slide back into its cubby hole under counter.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

Followed video instructions step by step.
I was fortunate i had enough slack in water, electric and discharge lines to avoid disconnecting.

Two wrinkles
1. wire clips on my door had to be pulled/pried loose from door and there were two not one

2. could not slide dishwasher out after lowering adjusters and figured out it was the mounting tabs bumpimng the granite countertop, thus the use of putty knives to slide the dishwasher out.

I replaced the User Control and Display Board and it is working very well now. The important things that should be noted are to take off the door and to open the door cover by unscrewing it. Those screws are located at the bottom of the door and two are hided inside.

the hardest part was removing the door from the face of the washer. Getting the door off required accessing the sides, so I had to lower the feet so it would slide out of the recess it sits in.
Disconnecting the springs for the door was straight forward and simple. once those were disconnected, it lifted off the hinges easily. The seals themselves were simply press-fit into the recesses. the old ones pulled loose cleanly and easily.. the new ones pressed into place very simply and without any real effort.
Getting the door back on was a little problematic, mostly in getting the hinge pins to line up properly.. but once it settled in, it line up itself, and the springs were easily replaced. I re-leveled the dishwasher, and then ran it for a full cycle to ensure it wouldn't leak anymore.

Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.

De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.

I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.