Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
This set (Knob and Clip Assembly, Control Knob, Dryer Control Knob) allows you to replace the knob on your timer if it is damaged or missing. The plastic knob can break around its shaft, or the retain...
This is a replacement timer knob for your washing machine. To complete this repair you will need a pair of needle nose pliers. Turn off power to the washer before you start. Pull off the timer knob an...
This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the correct time and setting for your dryer. If your dryer will not start or shut off, the ti...
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drai...
This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action a...
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your ...
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at ...
This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning smoothly during a w...
This split ring is supplied by the original equipment manufacturer, and it is designed to secure the tub bearing in washing machines. It is a circular metal ring, with an outer diameter of 2 inches. T...
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Violet
February 17, 2023
I'm trying to find for the GE washer the back plate for the timer knob, I believe it is part number wh45x10146 but I can't seem to find it.
For model number GCWP1800D0WW
Hello Violet, thank you for your question. The part wh45x10146 is a dryer drum. You may be looking for the Backsplash PS6011712 which has the writing on it. For example, whites, permanent press, load size etc. Or, maybe you are looking for the Dial PS1482363 ( that has a small indicator line or arrow) that goes directly behind the Timer knob. We hope to hear from you soon.
My dryer only stays on if I hold the start switch to on. When I release switch all cuts off...Everything else gets power and works when I hold the switch.I have replaced the start switch and the door switch. Is there a relay switch that I may be missing? Kindly assist
For model number GCWP1800D0WW
Hi Raymond, thank you for reaching out. As you have already replaced the start switch and the door switch, we would suggest checking the drive belt first. If it is fine, the issue could be with the drive motor and inverter assembly, part number PS8746234. You may need to replace it to fix the issue. We hope this solves your problem!
Hi Janmes,
Thank you for your question. If the washer is not filling with water, make sure that both the hot and cold water faucets are completely turned on and that they are in the proper position and not kinked. Then inspect the inlet hoses to see if they are clogged. If they are remove and clean them out. Place the hose ends into the tub or a bucket and turn on the faucet to verify that you have adequate pressure. If not, then remove the hose from the faucet and inspect the screens for dirt accumulation or damage. If you find any issues when performing the checks above, you will need replacement hoses and screens. If the inlet hoses and screens are fine, the issue may be with the water inlet valve. Before removing and inspecting the water inlet valve, unplug the washer from the electrical outlet. Then inspect the screens on the water inlet valve to see if there is debris or any damage. If they appear fine, you will need to test the water inlet valve for continuity with a multimeter on the Rx1 setting. The reading should be between 200 and 500 ohms. If you get a reading outside this range, you will need a replacement water inlet valve. We hope this helps!
What is the capacity? Is it larger than 4.5 cubic foot?
For model number GCWP1800D1WW
Hello Joseph, thank you for reaching out. The capacity of your model is 3.7 cubic feet, which means it is not larger than 4.5 cubic feet. We hope this information is useful!
1 person found this helpful.
Did this question help you?
Thank you for voting!
Violet
February 17, 2023
Thañk you for yr adviçe regardiñg the back plate for my timer knob you said the proper part # you said was ps1482363, do you know where I can order one please
For model number GCWP1800D0WW
Hi Violet,
Thank you for your question. The back plate or dial can be purchased through us. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
Did this question help you?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
