GC2228EEDB Maytag Refrigerator - Instructions

Ordered the parts, snapped them into place on the basket and then slid the arms into the holes on the freezer door, very very simple..

The best part of the repair was how easy it was to find and order the part. Instead of searching the parts houses around town I just went to the PartSelect web site, quickly found and ordered the part in about five minutes, received the part the next day at my home and was ready to make the repair. Wow! What a pleasure for something to work the way it was meant to. Removed old switch located by prying out with sharp knife or screwdriver. Don't worry about breaking it or cracking plastic. Disconnect(unplug) wires from back of switch. Replace (plug-in) wires on back of new switch. Insert in location of old switch. Finisheed.

Took out lower shelf. Unscrewed screws holding two broken shelf supports and removed broken supports. Replaced with new supports and screwed in the screws. Nothing to it.

Pried out ice blade bar and removed broken water fill cup and replaced with new one.The whole repair costs $9.52 So I saved $ 190 over the cost of Appliance man visit!
It would have been $150& $50 for visit to replace ice maker unit.

removed old shelf.... cleaned where old shelf was.... installed new shelf.. job completed in 5 minutes

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

have always done it myself, but Maytag store closed, so I didn't know where to purchase filter

I received it from Parts Select, in 2 days and if I remember right, price was cheaper than I paid last year, at store.

Repair requires the removal of the bottom hinges on the doors. No problem for the refrigerator side, but the freezer side has wiring in the freezer door for the water/ice dispenser, so have some wood blocks handy to prop it up. Biggest challenge is that in the center of the kickplate there is a mounting screw (Torx head) that is behind the kickplate and runs vertically. I removed the old kickplate without removing this screw, just broke the kickplate off. The screw is very difficult to access with any tool. Removal wasn't too terrible because the old kickplate was gone; but insertion with the new kickplate in place was a challenge. I used a Torx socket, but because there isn't enough clearance for the ratchet, I held the socket into place by wedging a large flat blade screwdriver between the bottom of the socket and the floor. I was just able to get my index finger under the new kickplate to slowly turn the socket to fasten the screw. Unfortunately I didn't feel as though I could skip the screw - without it the kickplate sags in the center.

Most of the time was sent to removing and replacing door shelves. Pry off upper hinge cover. Easy, it's only plastic. Remove 3 fastener from top hinge and remove hinge. Lift door off lower hinge. Lay door down on table let handle hang over edge. Remove door closer attach fastener. Remove and replace door closer. Pry lower hinge up and out. Tap new lower hing pin into place. Replace door, upper hinge and hinge cover. Had to replace Door Closer and Hing Pin together; both were worn and needed replacing.

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.

I simply removed the old brackets and replaced with the new ones. Can't get any easier than that!

Poped ou the old switch, connected new switch and pushed back into socket.

replaced electric control board, defrost for six hours. next day (24 hours) same problem, dusterhoff2928@charter.net

I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!

Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!