GC2227EED5 Maytag Refrigerator - Instructions

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

No tool required! Pulled out tray, emptied ice into large bowl for reuse. Pushed in and pulled from inside the coil springed auger until could get old plastic ring off and put new one on. Useing care not to apply too much pressure to ice dispensing end so as not to break housing. Have to turn auger assembly at an angle to compress enough and get old ring off. Needs a little physical strenth & care not to force plastic housing to breaking point. Worked great reused saved ice. Took less than 10 minutes

Removed broken dairy door (no screws or any tools were used) and replaced with new one purchased from partselect. It took me less than a minute to do :) thanks!

Very easy to order from parts select. Took seconds to replace.

Used the flat head screw driver for leveage to pop the door off. Replaced the chill door by placing at an angle and snapping it into place. Works perfectly!

Replaced filter with by-pass plug. For some reason though, ice maker does no longer functions, although there is flow out of the cold water tap. Is the design of the bypass plug such that, when installed, it impedes flow to the ice-maker?

Thanks

Removed the inner door panel held on by 30 small nuts crews. Removed the old seal. Stretched new door seal onto inner door panel. Attached inner door panel and seal to inside of refrigerator door. Using a magnetic nut driver was the answer in the tight spots and the small nut screws. Everything works fine and the beer is cold again!

First we removed screws in the top hinge, then lifted the door up and off the bottom hinge. Replacement of the door closer and lower hinge pin took less than a couple of minutes. Then putting the door back on and screwing the top back on was nothing.

We additionally replaced the puriclean filter which simply was twisting it off and then the new one back on

Replace the refrigerator lightbulb while traveling 88 mph then turned on the flux capacitor being carful not to get stuck in a worm hole. This allows you to fix the problem before it starts to go bad.

Took a putty knife and
Removed the old switch removed the spade terminals from the old switch and replaced them on the new switch and just pushed the new switch back in place

This replacement glass shelf arrived the very next day-after it was shipped. I was so impressed with the easy method of ordering and the prompt delivery of this product-also, the quality of the shelf was perfect. Great service!! I would recommend this for everything-as far as parts needed for repair or replacement.

I watched your online video on how to take out the old filter, and then to replace it with the new filter. It was as easy as on the video. Thanks!

Viewed the repair video. Removed covering. Replaced limit switch, control board, and solenoid. Very easy repair!

I followed the directions from John from Virginia Beach, with the added warning: Unplug the electrical connection and bring the whole ice enclosure out before you remove screws holding the relay and motor to it so you can see how it goes together. When you remove the relay, notice that a metal cylinder (Michael from Vienna Va calls it a magnet) slides out of it. If possible, keep this unit together. If it comes apart, notice there is a spring on this metal rod. Don't lose the spring and remember how it all goes back together. This job was just as easy as it should have been.

It is the model with the french door. I unplugged it, removed two screws at the bottom of the door, while holding the door from sliding down. Removed the door and put it on its side. Removed one screw that was holding the hinge, removed the hinge and replaced it with the new one. Put the door back on (do not forget to reinstall the shims).
Did the same thing on the other door. After putting the door back on readjusted the height to level the door, using height adjustment screw. Lock the door in place. It now works better then new