EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Back
Keep typing for more specific results...
Keep typing for more specific results...
Models > FTF2140ES2 > Instructions

FTF2140ES2 Frigidaire Washer - Instructions

All Instructions for the FTF2140ES2
61 - 75 of 425
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Front control panel cracked in several places
1. Remove two screws in back and slide top up an back a little. 2. Remove soap tray by depressing button in back. 3. Unscrew control panel and pull out. Unplug electrics from wall. 4. Unscrew electronic panel from control panel console and re-attach to new console making sure control buttons are correctly aligned and in place. 5. Screw control panel back onto washing machine, replace top with screws in back and slide soap tray back in. Boom, you're done!
Parts Used:
Control Panel Console
  • Eugene from Hadley, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
9 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spin Cycle wouldn't work
Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.
Parts Used:
Drain Pump - 120V 60 Hz.
  • KEITH from BEND, OR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
10 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer door woild not lock and would not allow washer to operate
Removed top cover of washer to get to the door lock mechanism then used a phillips head screwdriver to remove door lock mechanism. I then replaced door lock mechanism with the new one I bought from PartsSelect. The repair job was very easy and took a total of 15 minutes to remove old part and install new one.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Kevin from Merrimack, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
9 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would not spin out
First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.

THANKS
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Linda from Dover, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
11 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer door handle broke
unscrewed the old handle, and screwed the new one on. It only took 2 minutes to fix. Very easy!!
Parts Used:
Door Handle
  • mandy from rock falls, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking from inlet hose area.
Close examination revealed cracked plastic inlet area. I removed top of machine any carefully was able to loosen an pull damaged (froze over the winter) part back to remove. Attachment screws difficult to access, had to use magnetic screwdriver attachment during reassembly. Always iffy when working with plastic parts.
Part arrived 2 days later, took about 40 minutes to install.
Parts Used:
Water Inlet and Dispenser Valve
  • Andrew from Mastic Beach, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
tab broke off when the door was shut too hard.
2 screws and about 48 seconds of work. very easy.
Parts Used:
Door Striker
  • scott from albertville, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
9 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door slammed shut
door not level son slammed shut and door strike broke
Parts Used:
Door Striker
  • May from Abilene, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Kenmore 417.41042000 Front loading washer shakes
Paid $27 total for a shock kit to replace the 2 broken stock shocks. Replaced them. It turns out it was not the problem, but just a symptom of the spider bracket (mates inner SS drum to drive shaft) corroding and breaking causing the drum assembly to shake out of balance. Found out is a systematic problem with this model washer, and no matter what else you fix, this will break and kill it at some point. Piece of crap!
Parts Used:
Shock Absorber Kit
  • Chris from Burtonsville, MD
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
8 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No spin
No spin, water+drain worked playing with settings. Dart 1-door switch. Got code-tested motor-ok. Replaced motor control board
Parts Used:
Motor Control Board
  • Matt from MAPLE SHADE, NJ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door handle broke off at the top
Like another commenter, my teenage daughter ripped the handle off at the top in a huff. My husband simply unscrewed the broken handle and replaced it with the new one. We now make sure to open the door from the middle of the handle, not the top.
Parts Used:
Door Handle
  • Mary from Oswego, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not spin or complete spin cycle
E47 error code means control board or door lock. From reading other stories, I decided to try the door lock first since it is much cheaper. Frigidaire tech support was no help at all.

First I removed the "wire" and spring that hold in the rubber seal at the door.

Then I removed the 2 screws that hold the door lock in place.

Removed the door lock, unplugged the 3 connections, plugged the connections into the new door lock, screwed it back in and replaced the rubber seal and wire that holds it in place.

Runs fine now.
Parts Used:
Front Load Washer Door Lock and Switch Assembly
  • Jonathan from Littleton, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wet clothes after spin cycle on front loader
Found that the fill valve was leaking and clothes would be wet if not removed right away.
Removed 2 screws from back of top panel and removed panel.
Disconneced water lines and two screws held valve assembley to detergent dispenser and unplug wires from the 3 solenoids
Parts Used:
Water Inlet and Dispenser Valve
  • Tracy from Brazil, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door handle to the front load washer had broken off
Very easy. Remove 2 screws from the inside of the door. Take out the broken pieces and screw in the new one using the old screws.
Parts Used:
Door Handle
  • Francine from Wolcott, VT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt was still on washer, had developed a loose tear
Very easy to replace belt on this model, belt had spilt and the loose rubber was flopping around and dislodged plug from water pump. Washer would not start cycle, display showed (no spin). Removed back access panel with screwdriver. Spin the pulley and slip belt off pulleys. New belt is very tight but it will go on, no tension adjustment on this model. Thanks part select quick service will order again from this company.
Parts Used:
Drive Belt
  • jeffrey from mount juliet, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FTF2140ES2
61 - 75 of 425