FRKIT94 Whirlpool Ice Maker - Instructions

I took the front panel off the ice maker. Found the contacts on control board were burnt. I called Partselect, told them my model # and they directed me to a new control panel. 4 screws later I had part back on and ice makin.
Thanks Partselect!

John Long

My husband is a plumber...but did not have time to make the repair. So I took it upon myself!

Super Easy!

1. Unplugged Fridge
2. Unscrewed the 3 screws on motor
3. Pulled out old motor
3. Had to pour some hot water to melt ice cubes that were currently in the shoot. (because the new part would not line up correctly because of the frozen cubes inside the maker). Then soaked up all the water with towels.
4. Inserted the new motor
5. Put 3 screws back in.

ICE, ICE BABY! Within a couple hours it was dropping ice into the bucket! Husband came home, and I told him I fixed the ice maker (his expression was of dread)...and then he checked it out and all was perfect! So proud!

I determined that the plastic lever inside the icemaker was broken and I found the part easaly. It was farelly inexpensive considering the important job the ice maker does, so I order it and paid for the standard, 5-8 days delivery. To my surprise, it was delivered (to my neighbors house thanks to the delivery person) the next day. Once Berry the neighbor delivered it to my house, 15 minutes later ice was being made. I had to remove one screw and losen two on top of the icemaker, disconnect power and remove the icemaker. I don't think that this step was even required but I wanted to remove all of the old ice from the maker without thawing out the freezer. Replacing the part itself also required removal of three screws. I think that almost anyone can do this easily (with or without Berry).

unpluged the refrigerator, remove three screws holding ice maker in place, disconnected wire clip, removed front of icemaker by relaesing two clips holding it in place. the module and motor assembly are held in place with three screws. put the icemaker together and replaced it in freezer, and pluged the cord back in. the icemaker started making ice in about 15 minutes. very easy fix

removed icemaker timer/controler replaced with new part.reinstaled it works perfectly

I removed the two screws that hold the ice maker door. I then removed the single screw on the right underside of the ice maker. I depressed the plastic "catch" on the left underside of the assembly and the whole thing just pulled straight out. I then disconnected the wire harness.

The module cover is removed, then the module itself is easily removed by removing three screws.
The assembly is just as easy.

A few hours later, I had a half bucket of ice!

Removal of the Ice Maker required the removal of only one screw from underneath the maker and the power connector disconnect. Dis-assembly was straight forward. Remove old tray and heater, and reassemble with new tray and heater unit. Reinstall Ice Maker! Special Note: Allow the Ice Maker time to cycle through it's sequences. It may take a period of time before it starts producing ice after re-installation.

First I replaced the thermostat. (from this company.) Same thing happened. Then I thought the ice heater has too low voltage and does not melt it for extraction. So, I put a short on the relay on the beam receiver board. No difference. Then completely disassembled the ice maker, and discovered the shaft cracked on the plastic gear, which rotates the ice extractor. So, I ordered and received this control assembly. Put together the unit and having ice again. Due to the cracked gear the thing was out of timing. This gear drives the contactor for letting water in, freezing time, heating the ice, (so it slides out easily), etc

The first thing I would like to say is thank you Parts select for a very fast delivery. It was within 24 hours I received my component. The installation went very well. The main thing is to take each part off the old mold, one at a time and install it onto the new mold. Make sure to look at each part as it is mounted to the old mold and re install them the exact same way. Just be gentle with some of the plastic pieces because they are fragile in certain areas. It will take a few hours for everything to start working properly. Thanks again Parts select. Good luck and God Bless.

replaced icemaker motor.easy peasy

Remove the ice maker with two screws in the side and one screw in the bottom. You don't have to completely remove the side screws but you do have to remove the bottom screw.
Lift up on the ice maker and reach behind it and unplug the wiring harness. The tube that lets the water in is accessible from the rear of the fridge. Remone the water line, its only finger tight, and remove the two screws. Pull the tube up and out. Thaw it out with hot water and reinstall. With the ice maker out and on the table, pop off the front cover. Remove two phillips head screws and slide the cube tray off. watch how everything is placed before you slide it off. Slide on the new tray and reinstall all screws. Reassemble in reverse order that you took it out. Your ready to make ice...

Went very easy, watched the video from the web site and did what it showed to do and put it together and it worked.We now have ice.

Followed the handy repair video on this site for that part. Repair went exactly like the video described.

Real simple: Unplugged refrigerator at wall. I just removed cover by wiggling it off and removed three phillips head screws, lined up shaft with motor assembly slot and screwed in the three screws, plugged in and waited to make ice. Wasn't sure if it was going to work took about a day for ice to be made consistently. My repair man gave me an estimate of $185.00 parts/labor I did it for $65.00. This is the second time I have had to replace this part. This refrig. is about 15 yrs. old and still works great.

I followed the instructions that were given online by Kitchenaide. The ice maker came out really easy. Took 3 screws out set the new motor assembly in put the screws back in and reconnected the wiring harness. the unit slide back in easy. Works great!!