FPBS2777RFD Frigidaire Refrigerator - Instructions

Just place new filter and lock it!

FOUND ONLY TWO MOST COMMON FAILURES, NO ICE OR WATER KEEPS RUNNING/FILLING FREZZER. MAY CASE NO ICE BUT WATER CONTOL VALVE WORKED. REMOVER THE 4 10 MM BOLTS ON FREEZER DOOR AXCESS TO THE THREE PHILLIPS SCREWS ON BOTTOM OF ICE MAKER DISCONECT WIRES, AND LIFT OFF HANGERS, REINSTALL ALL REMOVED PARTS. NOTE! DID SHUT OFF AND DISCONECTED POWER BEFORE REPAIR. WORKS FINE NOW.

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arrive.

Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HOLD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

The first order arrived in a huge box and there was no scew to be found, the box had wholes in it. I was given a refund and told to order again.



The repair did not happen and the set screw which was actually recieved the second time was returned because it was the wrong size.

Just replaced and adjusted the amount of water that went in.

i only ordered 1, so i replaced each 1 then moved to the next. still no light, so it must be someting else. will try to check the wires with a volt meter to see if i have power next. something wierd happen, when i accidently touch the back of the led board, it lit up, small but still light up. hoping that means the led board is goo, must be in the wiring. i saw it had a main led board so will check the power to that.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

Used socket set and screw drivers to attach ordered hinge, thankfully we had the screws just not the hinge. Wonderful to be able to find and order on line! Thanks so much!!!

I followed the instructions from your website that I found when ordering the part. It could not have been any easier if I had set in a class room environment. Thanks for all the help and saving me the cost of having someone do a 15 minute repair for 1 hour of labor cost. I would definitely use your site again in the future and I have already put a bug in a couple of my friends ears for if they have issues in the future!! Thanks again!