FGR211AS2 Frigidaire Dryer - Instructions

My wife was able to easily do the repair before I could get home from work to do it. She watched the PartSelect video on her iPad as she did the necessary steps to get the belt replaced. We only needed one glide replacement, as one was still attached and intact. We should have purchased both sets of felt seal replacements, though that wasn't as urgent.
My wife thought the repair was quite easy overall.

I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.

The internet is a magnificent thing!

Raise the top and remove the front panel assembly. One philips screw, 24mm gas line coupler and 3 electrical connectors frees the burner assembly. Slid the old igniter out and the new one in.2 philips screws to remove the coil retainer and replace the coils.

As others have described in more detail... I lifted the top, removed the 2 screws holding the front panel (one on each side, inside the control panel on either side - not the easiest to get at, but not too bad), popped the clips holding the front panel in place and removed it. With the front panel off, the location of the coils is obvious (lower left side). The only challenging aspect of this repair is that the 2 screws holding the coils in place are really torqued in so it was crucial to use the exactly correct size screwdriver and not let the screwdriver slip while unscrewing those screws. Actually swapping out the coils took seconds, of course they have to go in exactly the same way as the old ones. I did take a few minutes extra to vacuum out years of lint from the inside of the dryer. Overall, much easier and cheaper than I was expecting and now I know where everything is inside the cabinet.

removed the top of dryer, pulled front panel back from drum and installed snubber(Front Drum guide).

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

after numerous holes put in my families clothes i looked on line and found "partselect.com". i ordered the front drum glide after seeing a similar story about the clothes being torn and getting caught and my family and i have our new dryer back!! yeah :<)

Popped in the new door catch! Tightened the hinge screws( which work loose and allow the door to droop. The reason the catch broke!) Also put red Loctite on the screws in an attempt to keep them from backing out again! Working great so far!!!

Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.

Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.

The repair requires the front panel to be removed. First remove the top by removing two screws in the back of the top panel. Once the top is removed, you have access to all of fasteners for the front panel. I removed the control panel to give myself more room. Simply remove the wire connectors on the panel and two connectors in the upper right of the cabinet. There are four screws that hold the front panel on, two on the inside about a third from the top and two more on the outside at the very bottom. Once the screws are removed, pry the front panel from the machine since there are spring clips holding the panel to the machine. Once the front panel is removed, you have access to the guides and the felts.

1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.

Simply popped it back into place, careful not to break the new handle.

Just replaced the new lint filter with the old lint filter. The part fit perfectly. I did not have a problem.