FFHT1515LWA Frigidaire Refrigerator - Instructions

I removed the shelf that hold's the rail's then one (1) screw that hold's the rail in place then I replaced the shelf. Simple & Easy!!

I watched the video online. It was so easy! All I needed was a screwdriver. It looks great.

Drawer support held in by one screw drawer slide in no problem

Took out the broken piece, replaced it with the new support using only a screwdriver, and VOILA, it was finished. Thanks!

I slid out the old drawer and slid in the new drawer. Easy as that! I would recommend this website to anyone.

After waiting over 2wks for my part to arrive, I purchased the part locally and made the repair the same day as I am still waiting for the part to arrive from you guys. Your customer service really needs improving. I paid for 2 day shipping, what a joke. I will be returning the part as soon as I receive it thanks.

Twisted replacement bulb into place easily. Let there be light!

it was very simple, my husband did it. had to take the top shelf out and screw in the support rail and that was it. couldn't have been any easier. this was the easiest process from start to finish that we ever had. looked up on line, found your website, ordered the part and it arrived in a couple of days. So easy and your company was most efficient in having the part and in processing. Couldn't have been mored pleased.

I unscrewed the old handle. lined up the new handle and screwed it back in.

After checking the capacitor and 3 in 1 starter run relay for continuity and both measuring , I was able to remove the old parts and install the new parts for the refrigerator after unplugging the unit. I also checked the new parts prior to installing. I also went on Parts Select and watched some very helpful videos. Thanks a lot for your help desk for going above and beyond to ensure that I ordered the correct part! ????

The service manual diagram shows the 149 complete fan shroud in a vertical (upright) position. Misleading! Of course.
The actual mounting of the lay in fan shroud fully assembled is in the horizontal position laying in a tray area just above the evaporator coil cage assembly. The entire shroud assembly can be installed incorrectly by the diagram and will still fit. BUT... no cold air will flow or be forced into the ice maker vent nor the refrigerator vent. I found this out the hard way by trial & error.
If the drawing had shown it in the horizontal position for both removal and reinstallation... it would have saved a lot of time and headaches. Also, the diagram does not show the (2) plastic angle supports on the shroud, another scratch your head event. Parts included on drawing... 149, 5, 8, 9, 13, 14 on CTFFHS2611PF4 diagram page of service manual.
ALSO, the (4) lower cabinet plate screws have to be removed, and the first left hand screw counting up to allow the next upper panel to swing out enough to lay the shroud in correctly (horizontal) on top of the evaporator coil cage. BOTTOM LINE... THE AIR FLOW HAS TO BE UP IN ORDER TO WORK PROPERLY.

removed the top shelve. Unscrewed the broken support rail and replaced it with the new one.Put the shelve back and I was done

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

From discussions with friends, I determined the problem might be easy to fix. The fridge made a lot of noise, but the compressor DID come on, and inside the freezer was cold, but the main fridge was warming.

After unplugging the fridge, I removed the fan assembly in the freezer (there were about 4 nuts and a couple of plugs to uncouple.

I could see right away the fan blades has broken off, but the motor looked good. The new new fan pushed easily onto the shift and fit perfectly in the housing.

I reinstalled the fan assembly, plugged in the fridge, and right away heard the new fan come on - very quietly. What was a roar became a whisper and the fridge was down to 38 degrees with a few hours.

I easily removed the shelf, cleaned it, removed one screw, adjusted a tab that was bent, then installed new side rail with the screw that was removed and put back the shelf and storage bin. Everything worked perfectly. I must have saved $100 by doing it myself.