FFFS5115PW0 Frigidaire Washer - Instructions

I didn't have the right tool, so asked my handyman neighbor to come do a few projects and he had the driver in his pocket screw driver. it is a tip that is included in many multi-tip drivers. two screws removed the old and replaced the new. cheaper than local parts place, and no repair man. thanks

very easy, just put in the 2 screws and it was fixed..

Took off top. Removed 2 screws on Door Lock Assembly and replaced.

You must remove the top of the washer with screws on rear of washer. Top slides forward to remove. Once top is removed you can reach door lock mechanism from the top. Two screws must be removed from the front of the washer where lock enters mech. You can grab the mechanism from above by the wires that run to it. Undo wiring harness and insert new mehanism. Slide into place and attach in the front of washer with screws. This job is easy and can save you a lot on repair bills!

Removed retaining band around door boot and prized-off boot on left side to access door lock - simple screw driver replacement job. Deleted last error code. BUT - washer worked again for several days, and now code E43 is back and won't spin - problem is intermittent - so suspect it is NOT the door lock, but a wiring or control board problem. Ongoing.

Take a deep breath and say, "I can do this. I will not pay well over $100 for someone else to come and do it."! Identifying part easy, mail very quick, web instructions clear, took out two screws, slipped out old part, put in new one, replace screws. I loved every minute of it and it cost $16.20 (part and shipping). Thanks, Part Select!

Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!

I found this wonderful web site, after removing the cover and running a diagnostic to find it was either the door lock or the TCP control board. Control board unable to find any information on was scared to call the repair man as they usually cost about $500.00. I am a single mother and order the door lock and just like that I was able to repair it myself. Thanks you so much!!!

Unable to get the door hinge off the machine after 6 years, one screw would not budge and was beginning to strip the head. If you take the door apart while still mounted to the hinge, you must have another person hold the door pieces securely, or you will likely break the tab on the front door piece that fits into the hinge bushing. Don't let that happen! Easy does it, hold it still, unscrew all the screws and gently pop the inside piece away from the outside piece, HOLDING IT SECURELY. Use gloves so you don't get cut, that glass is really sharp. Good idea to use some masking tape and cover the cut edges...I thought of this too late...wish I'd have done it. Lining up the bushings is probably the hardest part while getting the front and back pieces together with the big glass bubble secured, and again, HELD SECURELY by another person. This really was easy, but I wish someone had mentioned whether to take the hinge off or not, unfortunately, I could not. I had to get creative, and the fix was perfect, even if I did initially break the tab that lines up the bushing...I wasn't spending ANOTHER $90 for the teensy tab being broken. It works perfectly with my fix - but it won't if you can't fix that tab! I was glad I didn't have to call a repairman!!!

Unscrewed two phillips head screws, removed damaged part, screwed on replacement part. Presto! Washer works again. I especially appreciated receiving the part less than 48 hours after I ordered it with only regular shipping charge.

I am a 64 year old female that had never attempted to fix anything. This was my 1st attempt at fixing something. It took longer to look for phillips screwdriver than it took took to repair it. Thank you so much for instructions.

Simple removed the screws from the door, did this the night I broke the glass. Gently pryed the inside of the door apart from the front of the door panel. Lined up the arrows on the edge of the new glass panel with the inside of the front door panel and placed the inside plastic door panel back on, to hold the glass panel in place. Replaced screws. Everything worked great! Easy, affordable fix!!

two screws took off the old plate, replaced the door strike with saame screws

I order the part from this website. I want sent to me in 1.5 days. I removed the srews form the broken latch on the door. I place the new latch on the door, than use a phillip head screw driver and attach the latch to the door.

Followed your instruction,simply removed the top cover and the two screws on the door to remove the switch assembly. Unplug old part and replaced with the new one after pluging three wires. I saved $105.00, which was the quote from a repair shop. Thank You for your great service and directions; the part arrived a day after I had ordered, did not pay extra for special delivery.