All Installation Instructions for Frigidaire Range FFEF3013LMF

clock/timer didnt work

unplugged appliance.removed back panel.removed old clock/timer by backing out 4 screws holding it in place.took of each wire one at a time as not to confuseplacement on new part. peeled front plate of old timer very carefully, placed on new part.put back in place.very easy, less than half hour.if I can do,anybody can

Parts Used:

Electronic Clock Assembly

jack from chambersburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

switch not always turn off

Took upper back off ( 6 screws), chech to be sure was right switch, pulled spade clip wires of, put on new switch, checked to see that it worked, replace cover.

Parts Used:

Infinite Burner Switch - Large Element

Jerrold from San Marcos, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

7 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven racks rusted

Ordered new racks and replaced them.

Parts Used:

Oven Rack

Wendell from Ocala, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

11 of 21 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven wasn't heating properly for a few months and then stopped altogether

The hardest part was pulling the oven away from the wall. Two bolts hold the sensor in place and a clip connects the electronics. Replacing the old one was trivial.

Parts Used:

PROBE

Matt from KENNETT SQ, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

2 elements stopped working.

My husband followed the video instructions and it was easy to fix.

Parts Used:

Radiant Element with Limiter - 1200W

Ruth from MORGANTOWN, WV
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

8 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Refrigerator Light bulb went out

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Parts Used:

Light Bulb

ANGELA from MEBANE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

7 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

When bake button was pressed the oven did not work

Unscrewed upper back panel of stove. Connected wires from old part to new part one at a time. Then unscrewed old part from stove. After that I screwed the new part to the stove. Replaced upper back panel. Finished.

Parts Used:

Electronic Clock Assembly

Curtis from Anna, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner indicator light lense broke off

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

Parts Used:

Light Lens Indicator

Kathy from NEW BERN, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

old element coil burned apart breaking the circuit.

removed the old burner and put the new one in it's place.

Parts Used:

Radiant Element with Limiter - 1200W

James from WARRENTON, MO
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

switch had a diffirent lug configuration

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

Parts Used:

Infinite Burner Switch - Large Element

Robert from Andrews, SC
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

9 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gasket missing

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

Parts Used:

Oven Door Seal with Clips

CHERYL from PERRYVILLE, AR
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven not heating display light out

first i remove cover, then i unscrew defective part, remove wires. i then install new part & replace marked wires . I then replace cover, turn on oven and holla! my oven is working.

Parts Used:

Electronic Clock Assembly

Manning from Medley, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rusted leveling foot

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

Parts Used: