FEF364FWA Frigidaire Range - Instructions

I had to replace the switch in the back of the control knobs. I was very grateful to the female phone attendant who answered my call. Since my part number had switched a few times, she took the time to reverify the "blueprints" of my machine with the parts carried at Parts Select and she helped me be assured that I was buying the correct part for my machine. She was SOOOO helpful. Will definately buy again from your store.

First I unplugged the the stove. I then unscrewed the two screw holding the element. Because I had read the other repair reports on the site, I was very careful in pulling the element out so I wouldn't lose the wires in the rear of the stove.
Once out, I held them with the pliers and gently pulled the element until it was loose. Plugged in the new element screwed it back in and plugged in the oven. Worked like a charm. By the way the part arrived the day after ordering it!!!! This is a great site.

I disconnected power cord. Removed cooking racks. Removed element mounting screws. Removed back panel and removed wires on both ends. Pulled element out put new one in and bolted down. Reconnected wires. Put rear cover on. Plugged in and checked for correct opreation. OK!

Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim

Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

First I removed 2 screws that held the stove top in place. Raised the stove top and support it. Then, I removed the hold down spring for the burner and removed three wires from the old burner. I found that the connector on the white wire was spread open too much so I crimped it closed for a better fit on the terminal. I reattached the three wires, put the hold down spring back in place, lowered the stove top and installed the 2 screws. JOB DONE

The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.

killed the 50 amp power. removed 3 screws from above oven door slid out cook top, dropped brace holding 2 front burners. The connector corroded off had to look for a high heat connector to connect to the element, after that just screwed everything back together.

I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.

REMEMBER TO UNPLUG YOUR APPLIANCE FIRST!

Started by replacing element which was clearly broken. Still no heat. So then I changed the oven sensor. Was disappointed that when I received the sensor I had to cut and splice the connector that was on it with the old one that came off the old sensor. Did that and still no heat so I had to buy a new clock/timer. Went to another store for that because of the connector not being the right type and there was no picture of the clock/timer like the other website. Overall ok, normall troubleshooting steps, just wish I didn't have to cut and splice the connector on the new sensor I purchased from here.

TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE

All of a sudden, one element in our glasstop range would not light and heat up. My wife and I were not sure what to do. Looked it up on the internet, found that you can do it yourself as others desribed the process of accessing the elements below. We decided to do that. It takes two people as one is holding up the glass because it opens like a car hood. While we diagnosed it was not a wiring issue (found a burnt wire, rewired the burnt wires (after mending the non burnt portions) to another element. The element that was not working before still did not turn on. Decided to purchase an element. While many online places sell elements, PartSelect actually allowed searching by brand with exploded views of the range to select the exact parts. This lessened the worry of purchasing a wrong element. When the part came (almost one day later), the repair was less than five minutes. Thank you PartSelect. I feel I saved a lot of money and aggravation.