EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
Back
Back
Back
Keep typing for more specific results...
Keep typing for more specific results...
Models > FED355ESF > Instructions

FED355ESF Frigidaire Range - Instructions

All Instructions for the FED355ESF
106 - 120 of 183
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Control will not work - only clock blinks
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.
Parts Used:
Main Terminal Block Kit
  • Sue from Lampasas, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
0 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken globe in oven and burnt out light bulb
Easy as 1-2-3
Parts Used:
LENS Light Bulb
  • Sharon from Foley, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
0 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove door switch was broken
used two flat bladed screw drivers to get under edge of switch.. pried one side up and unit popped loose... removed electric connection (three prong recep) and plugged in new switch ..pushed into hole and was done... approximately 3 minutes..
Parts Used:
Door Switch
  • James from Milford, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven was not heating up to the set temperature. Stopped around 180-200F.
Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 degrees. So far, works great.
Parts Used:
Temperature Sensor
  • Robert from Glasgow, MT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced burner drip bowl
Very easy to remove the old drip bowl and replace with new ones.
Parts Used:
Chrome Drip Bowl - 6" Drip Bowl - 8"
  • Irene from Rochester, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Handle
Really easy to replace handle. However, because the new handle does not have the metal inserts to receive the attaching screws (!appearently a bit cheaper to make!), I am concerned that it will not last as long. I could find no reference to new attaching screws so used the old ones...hope it works!
Parts Used:
Door Handle
  • Charles from Lake Mary, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burner burned out
unplugged old burner plugged new one in
Parts Used:
Surface Element - 8 Inch - 2600W
  • Charles from Kettlersville, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
8" left front surface element would no longer heat properly
I ordered the exact replacement element, and after unpacking it, it took about 5 minutes (actually,less; didn't time it), and the new element was installed and working fine.Thank you very much.
Parts Used:
Surface Element - 8 Inch - 2600W
  • Robert from Greencastle, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Could not find drip plates in local stores
Just put the drip plates in stovetop and worked perfectly
Parts Used:
Chrome Drip Bowl - 6" Drip Bowl - 8"
  • Pat from Hendersonville, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Needed new drip bowls
The hardest part of the job was cleaning under the old rings. Cook top looks new again!
Parts Used:
Chrome Drip Bowl - 6" Drip Bowl - 8"
  • Judith from Jewell, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
element not heating right
Took old one out and plugged the new one into place.
Parts Used:
Surface Element - 8 Inch - 2600W
  • sharon from Summerton, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
handle broke
unscrewed old and screwed in new
Parts Used:
Door Handle
  • Gary from Reno, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Drip Bowl Replacement
I could not find the larger size universal drip bowl to fit the 8" burners on my stove. This product replacement is perfect.
Parts Used:
Drip Bowl - 8"
  • Jennifer from Arena, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
inner glass uncleanable
Took door apart, went online to partselect, ordered new glass, and put it back together. Oven looks like new. Makes sense to order the isolation as well when you do the repair
Parts Used:
GLASS
  • Krista from Newtown, CT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burnt door seal
with a schematic of the door, this was fairly easy. since we had to take it completely apart, we cleaned the glass as well and every little nook and cranny. Once we put it back together, the door looked like we just bought it. these days, with whats available online, scary jobs turn out to easy.
Parts Used:
Door Seal
  • CARL from MARSHALL, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the FED355ESF
106 - 120 of 183