F1403FD LG Washer - Instructions

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

Service guy came
all we thought was problem, was not. Need new maching soon.
But as far as service
Parts/this company
I would definitely use them again
Gal placing order was EXCELLENT
ARRIVED in perfect time.
Couldn’t use parts
Return policy great
Thanks to you all
J murray Az

Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power lines out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.

Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.

I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.

After reading thru previously posts by other people, I started:
1) Took pictures of inside door, the hook that involve with the handle and the hinge. So they would be very helpful as needed later.
2) Removed the whole door from the combo and lied it down,
3) Disassembled the door and took a few more pictures,
4) Replaced the handle,
5) Took a look at the picture of the hook in (1) then jammed the hole with a piece of card board that cut to fit the hole. Used tape to secure the card board. Made sure the hook was secured/tighten. (This step is very important because it will make the spring works with the handle properly later!)
6) Reassembled the door,
7) Removed the card board from the hole in step (5). If the hook was tighten as before you start, it will be ok. Meaning the spring was resting properly on the inner door behind the handle (If the hook is not tighten then you have to redo steps (3), (5) and (6) again), and
8) Made sure the handle and the hook were working properly.
I think If you follow the steps above it will be easier and faster to replaced the handle!

Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly!
I am a 63 woman and found this easy to do, with help from you tube guy.

It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time.
However, after replacing the door lock it was obvious that this was not the problem. I had to remove the new part and replace the old one.
For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.

After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires

It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done

When to utube typed in my problem, very easy fix

I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!

I took the washer completely apart and ordered any parts that looked worn and put it back together. It’s working like new and will last for a few years

My husband couldn't fix it. We called our Handiman/repairman. He had a difficult time and took 2 hours. $197.00 charge. This handle does work better than the original.

It's easy, I removed the two bolts that hold the door hinge on, placed the door on a protective surface, removed the screws that hold the cover on, remove the cover, take the old handle and spring out , replace with the new part and reverse the assembly.