EW28BS85KSEA Electrolux Refrigerator - Instructions

Removed 1 screw and unplugged flipper mullion assembly and removed it. Plugged in new flipper and one screw and done. Works as it should.

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arrive.

Removed exterior housing, sliding old unit forward to release. New unit went in easily. Caution wires don't get pinched.

I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from that point. Left handed threads by the way.

Secured bracket. Attached electrical contact to the compressor. Secured inverter to bracket.
Problem: the electrical contact cords are very short, therefore it wa difficult to reach the compressor. Even after connecting to the compressor, the cords are under stress.
However, the refrigerator is working fine.

Removed screw on Mullion so that the replacement hinge can slide onto the small plastic bracket on the door. Slid the mullion on the hinges and screwed in muliion (1 screw).

Following previous installation instructions was very useful. Would add that the nut driver needs to be 1/4 in and to release the water lines from the valve body, simply squeeze the blue ring toward the valve and pull on the water lines at the same time. Simple fix!

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

I had to tap the screw holes with a 8/32 tap so that the screws would not bind.

I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.

Undone the water line that comes up the back of the refrigerator and pulled the water tube out the back of the refrigerator and reinstalled the new one and reinstalled the water line. Done

1). Shut off water supply to fridge. 2). Move fridge out to gain access to back of fridge. 3). Remove poly line to water tube have a glass handy to catch any remaining water that might be in line. Some may have a foam insulating washer around water tube remove it first. 4). My Sears-Kenmore was a twist lock water tube have to turn it to left or right depending on brand to remove tube. 5). After removing make sure tube didn't just have water frozen in tube ( that was my problem ) run it under hot water frozen piece will come out. 5). Problem fixed, reverse directions to re-install tube!

1st a changed the defrost stat. Waist of time. Realized there was no evaporator above fan. Noticed ice was builing up behind ice maker near fill tube. Found if I shut off ice maker ice wasnt building up on fan. Moved fridge out unplugged fridge unscrewed plastic nut. Turned 90 degrees. Replaced tube locked in place . Screwed nut back on . Plugged in and turned ice maker on. Wife happy ice was back on and no noise.

I followed previous directions, and would recommend them! Briefly, I removed the plastic covers for the water filter, water tubes, temperature control switches to allow removal using a screwdriver and a nutdriver(I think)to remove the hexagonal screws. I also removed the water filter before beginning. I pressed the blue thingies in the back towards the base to remove the water supply lines. It was a bit tricky, and took the bulk of the repair time, but they came lose once enough pressure was applied. I took out the old filter base, put in the new one, attached the water lines, and put back all the covers. Everything comes apart very easily, and went back together very easily. A simple repair that had us back in ice and filtered water within an hour!

I was able to take away the trim covering the parts with a nutdriver. The base was disconnected using a phillips head screwdriver. The only real issue was how to disconnect the plastic water lines from the old base and connect them to the new one. I finally realized I just had to cut the lines where they entered the filter base because they would not pull out. I then finally understood that to install them into the new base I just had to push them in securely. The lines were long enough to do this but probably would not be long enough to install another filter base. In that event I do not know what all would have to be done. The leak had been going on for years (it only leaked when water was running to the ice machine or water dispenser). It is great having it repaired and we hope to get quite a few more years out of this old fridge.