EGR2001EM2SS General Electric Range - Instructions

I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.

The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.

They turned out to be 1/4 inch hex head screws. Only after soaking with penetrating oil could we budge them. There must be a special tool to loosen them on the back side where there is no room to get a socket on them and since they are in the heated part of the oven they are almost welded in. We were successful, but could only get one screw back in. So never use your oven with the door left open as I did if you do not want to repeat what happened to me.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Opened the back and installed the new one. The only problem was pealing the paper of the old one that shows the labels. Strongly recommend to buy that part also. The job will be more neat.

Removed the two screws that hold the oven bottom to expose the glow element. Also removed the lower draw to get to the connections. The job was only complicated by getting to the two bolts holding the glow plug to the oven frame. Getting them off and getting the new plug on was not easy with standard tools. There was not a lot of room to work the hex bolts and i wound up cutting the old unit out and attaching the bolts to the frame and cutting slots in the new unit so I could slot it in. That worked. The glow plug was the problem and the oven came right on.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Go to utube videos for this are there

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

removed bottom of oven.removed heat shield.i
then unscrewed the wire nuts to the igniter.i
then tookout the burnner with the igniter attached.
i unscrewed the two screws holding the igniter
in place,and put the new one on.i then screwed
the wire nuts back on,and put it back togather.
it works great,thanks for the help.it saved me alot
of money.

Checked on this website for ideas. A 20+ year repairman posted that the problem is the control valve and I should replace the igniter while I'm there. The valve was priced at $189 and the igniter $60. I decided to try the igniter first and all is well. Valve not needed.
Steps; remove; door, lower tray, and oven floor pan. Disconnect two igniter wires. Use 6mm sock to loosen gas feed tube, then lift tube up a couple of inches to access igniter screws. Remove them, and reverse process with new part. I tried to R&R the igniter without loosening the gas feed tube but it's a real PITA. Good luck, easy fix.

1. I have searched info on the internet and found that site.
2. Initially I could not figure out how to unscrew ingniter. After reading more post I have found out how to access nuts underneath.
3. After I have removed lower drawer and unscrewed metal cover and then inginter nuts.
4. I have got a part with two wires attached to the igniter and two porcelan insulator, so it was very easy to cut old wires and connect with an igniter wires in parallel

/||\
||

I removed the 2 screws that held the bottom oven plate in place. Then I removed the one screw holding the bottom burner in place in the front. I then reached into the rear area and unscrewed the last 2 screws securing the burner. I disconnected the igniter wires at their push-on connections and lifted the whole burner/igniter unit out. I relaced the igniter using the 2 attachment screws, and I cut the old igniter's wires with connectors and spliced them into the new igniter's wires, using the ceramic wire nuts that came with the new igniter. I reassembled the unit and it worked first time.

Followed suggestions of previous posts. Removed oven door, warming drawer, pan in bottom of oven. Removed element to replace igniter. One thing I would add is I put a small piece of electical tape on the heads of the two 1/4 in. screws for the rear element bracket. This kept them from falling out of nutdriver.

Following the recommendations of others I decided to attempt repairing the oven by myself. I unplugged the stove. I removed the oven door, the drawer, the drip pan from below the oven unit and the oven pan to access the igniter bracket. All screws were 1/4" hex head except the oven pan which were slotted. I disconnected the 2 wires. I removed the old igniter and cut the 2 wires close to the old igniter to allow extra length to splice to the new igniter. The new unit included 2 wire-nuts. It was simple to wire-nut the new wires to the old ones and install the new igniter. I reassembled the pans I had removed and the door. I plugged the stove back into the wall. The new igniter worked perfectly. My wife continues to tell me how great it is to have a working oven again and how much faster it seems to heat. I am thankful the oven didn't fail while we were cooking the Thanksgiving turkey the week before. I debated calling a repair technician or shopping for a new stove. The price of the new igniter and the description of the procedure convinced me to attempt a repair. I am very pleased with the results.