EB22DKXFN01 Whirlpool Refrigerator - Instructions

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

Most difficult part was finding where they hid the defrost timer. (it is in the left front under the fridge behind the kick panel.) just unscrew the two fastener screws from the front, tilt fridge up on one side, slide timer bracket back and remove. Unplug and remove timer from metal bracket. Replace timer and remount bracket.

I removed the ice maker with 3 screws after having shut off the water. I tried getting the part locally but thought it was a bit much. Of course after having had ordered the wrong part, PS51041 and having it over nighted here and paying the return shipping I would have saved money getting it locally. When I finally got the right part I used the power cable and level lever off the old maker and reinstalled the ice maker in just a few minutes with a nut driver and screwdriver. Thurning on the water in about and hour it started making ice. When ordering online make sure you can get a large enough diagram to see what you are getting. If you can't ,call their phone number ant talk to a live person.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Very simple fix, remove 3 screws, two connectors to the old switch

Emptied unit and removed screws holding panels at rear of freezer compartment. Removed panels. Removed two screws holding motor. Made diagram of wire locations and fan blade orientation. Removed three wires and fan blade from motor. Took new motor and installed wires and fan blade to motor. Installed motor with screws. Test ran frig and reinstalled panels.

Our refrigerator is about 29 years old. We were told once that a gasket repair would cost more than a new fridge. Not so. It cost about $230 for both the fridge and freezer gasket. We had some rust that had developed from not replacing them sooner around some of the screws. They had to be cut out and replaced with the next size up to hold well. We cleaned everything thoroughly including behind the door compartments. We took those off the door. The guy in the video doesn’t do that. We replaced our freezer insulation also as it had gotten wet and was completely frozen. Overall, it took much longer because of our neglect over the years and believing someone when they said to just buy a new refrigerator. We love this one again, as much as we did when we bought it. The gaskets fit perfectly and after taping the doors shut overnight, they seal extremely well. We are very pleased.

Removed panel and motor cover at rear of freezer compartment. This requires 1/4" nut driver. Removed motor assembly bracket and wiring, careful to note where ground, neutral and hot were attached. The entire assembly must be removed from the freezer compartment in order to swap new motor for old motor. Re-inserted assembly into freezer compartment, reattached wiring. Made sure all assembly screws were tightly fastened and wiring was correct. Re-attached panel cover and motor cover. I did note that a few of the 1/4" machine screws wobbled in the original holes; I used slightly larger, 5/16" head machine screws of identical length as replacements. New motor is much quieter. No longer sounds like a truck is idling in our home.

I loosened(but did not remove) the 1/4" sheetmetal screws around the perimeter of the door liner. (they are numerous and they are hidden in the fold of the gasket) I removed the old gasket. With the screws still loose, I installed the new gasket. After insallation I re-tightened the liner screws. Several gaps were noted and eliminated by gently heating the gasket with a hair dryer. (be patient , it takes some time)

There were no instructions with the new gasket which made the job difficult. After great difficulty I called an appliance store and learned that the gasket should be soaked for several minutes in very hot water to make it pliable and easier to install. Also, the plastic insert that the gasket fits into should only be loosened and not removed when inserting the gasket. Lastly, the door should be removed and placed on a table to allow leverage to be applied. Installing it while still on the door is almost impossible.

First we read all the comments by other handymen. This was really helpful. Then we took the door off and removed the old gasket with a nut driver. We tried to slip the new gasket under the edge with a thin spatula and didn't have much luck. Then we remembered someone saying that is was a good time to take the door apart and check to see if there was ice build up in the door. It was so bad we took out the frozen insulation and replaced it with new....$4.00 at the hardware store. While the door was apart we put the gasket on and put it in place and tightened it to the door. This worked very well for us. This saved us from having to buy a new refrigerator/ freezer. Thanks.

Slid the end caps onto the shelf, placed the tape on the pieces as noted in the directions, and put the shelf back in place. Fast service, exact part, easy to find on the web site! Great!