DW730B-CAN Jenn-Air Dishwasher - Instructions

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

I first made sure the new gasket was long enough and it matched the original. Next I used the tip of a screwdriver to pick out a corner of the old gasket and then pulled the entire thing out. I noticed the old one stopped at the bottom of the gasket well. The new one was much longer and I thought I might have to cut it to length. Well I'm glad I didn't. If you start on the right side and work your way up and around with a 2 in. piece longer then what the old one was. I carefully tucked it in the bottom and closed the door. Glad I didn't cut the new one. Instructions would have been nice. Overall an easy fix. I'm very mechanically inclined so I knew better.

First I replaced the door gasket as every one else. This cut drips about 30%. I then discoverd that the Rinse Aid circular dispenser cap was opened about half way. I turned the cap tightly clockwise to close and cut drips to 90% total. I czn live with the other 10%,

First I removed power to the dishwasher. The inside panel of the dishwasher door is held on with several screws with Phillips heads. Remove those and the panel comes off. There is a silver metal guard that you have to pull off being careful not to tear the insulation that is on the other side. Then there is one hex head screw to take off the handle latch assembly. You remove this assembly and take off the wires to the two switches on each side of the assembly. The replacement part doesn't come with the black plunger that pushes on the switch buttons so you have to remove it from the old assembly. This was the only difficult part, I essentially destroyed the old plastic assembly getting it out. But putting it in the new assembly was easy. Then I attached the wires to the switches in the new part and reassembled everything. Works like a charm now.

I removed the inside door cover, unpluged the accuator, removed the two screws holding the dispenser latch in place. Replaced both the latch and rubber groumet. returned the door to normal operation and verified no leaks was present.

Basket Replacement very simple just remove old and set new basket in place

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

First i bought inner door seal and that didnt work,so i read some of the other repair reviews and found that it was the soap cup latch gasket.When i removed the cover from the door you could see where the water and soap was getting in and running down to the lower right side of the door.Once i looked at the door latch gasket it was easy to see it was torn and worn out.I did replace all four gasket's just for assurance down the road.

Followed the instruction video provided by this site ! 15 minute repair?..Super Simple!!! I Love this company!!! Saved me a bunc of money!!

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

Removed old gasket and simply replaced it with the new one. Very easy.

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

Replaced with the new basket. However, the part had been replaced, and I do not like the new setup. One basket has been replace with 2 that are hooked together. Each basket has a cover, but it covers the whole side, not just a part. In my old basket, I had a part of the basket with a cover that could hold plastic lids and measuring spoons that can easily wash out of the basket and hit the heating element on the bottom. My "fix" was to remove both lids and use the lid from the old basket to cover one part of the new basket. It's not very satisfactory, as it is not hinged and had to be removed and tucked in each time!