DVLR223EEW General Electric Dryer - Instructions

First unplug dryer to prevent electrical shock. To remove the front of the dryer, open the door in top left and top right corners is a machine screw. They can be removed with a Phillips screw driver. Lift the top slightly and let front fall forward about 6 inches, lift slightly. Two wire will be connected to the switch in the door. remove the wires and squeeze the tabs on both sides of the switch and push it out. Push new switch in to replace old switch and reassemble.

Clips on the inside of the door handle had snapped off, 1 minute later it worked like new. NO TOOLS required! So happy my older appliances can have new life by the parts carried by PartSelect. Thanks!

My husband broke the door handle, but of course, i had to be the one to order the part & fix it. I ordered the part on the weekend and much to my suprise it was on my doorstep on Tuesday when I got home from work. Then I saw the part was shipped from nearby Louisville. I was overly happy with partselect!!!!! All I did was open the packaging and clip the dryer handle into the 4 holes. Easy as pie!!!!

Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

I've experienced same symptoms on previous dryers over the last 30+ years, so I immediately ordered a rear drum bearing replacement kit from PartSelect. Perfect replacement parts for replacement of OEM parts.

1) After unplugging dryer, moved it to garage because of expected dust and lint deposits.
2) Removing two screws under from top lip allows top to lift and rotate off of dryer.
3) Removing two screws inside on both sides allows the front panel to be removed. Just remember to lift drum when you pull pannel off.
4) Best to take front panel off completely, so remove single screw on green ground wire at lower left and disconnect the white two wire connector (pull apart). Three wires need to come off of door switch (yellow/brown and white leading from the dryer inerds and one white to the drum light). Best to tag or remember where they connect. Otherwise, white from inerds goes to switch common, y/b goes to normally open and bulb white goes to normally closed terminals.
5) Get someone with really skinny arms to reach in to slide drum belt off of idler pulley. Otherwise, long sleeves are a necessity to keep from getting sliced to pieces on sheet metal edges.
6) Lift drum out and away from dryer frame. It's a pretty tight fit so get a helper to spread the side panels apart a bit.
7) Replace both bearing pin in drum and bearing socket in heater pan, following instructions that come with the parts or the video that is on the PartSelect website.

Didn't expect the drum slides and top drum slide support to be worn out, so I had to order them ASAP from PartSelect. The slides were totally gone and the support assemble was effectively toast. You might seriously consider replacing the slides and the lower felt when you try to fix the squeeks, since they are a major source of the noise and take an additional 2-3 minutes to replace.
8) Reassembly of the dryer is just doing the above steps in reverse. Best to clean out as much lint/dust as possible, since a clean dryer is an efficient dryer and we all want to make our "green" friends happy nowadays.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.

Replace the front and rear bearings. When I have to do it again I will only order (3106), (313), 2x (316) green, 2x (316) white, and drive belt. Taking it apart and putting it back together was easy. Unplug the unit. Take out the 2 philips screws that hold on the top. Lift the top from the front to clear the locking tabs in the back and take it off. Take out the 2 5/16 screws that hold on the front. Tilt the front (door) forward and rest the drum on the dryer sides, you'll see it. Disconnect the wiring harness for the light and door switch, 2 wires. Lift the front off the bottom retaining clips and place aside. Have someone hold up the drum. Reach under and unhook the drive belt. Pull out the drum assembly. Take off the rear bearing, 3 screws. Clean out the heating element area in the back of the dryer while you have a chance. Replace the bearing assembly. I bought the entire bearing assembly but I could have gotten away with just the sleeve ( 3106), but I didn't know that at the time. Take off and replace the drive belt. Lock the tension arm for the drive belt into the compressed position shelf holder by the motor, push the arm down, you'll see it. Replace the drum and have someone hold it up while you rehook the drive belt and release the tension arm. Now, I would suggest replacing the entire front bearing. If the slides have been bad for a while, the plastic bearing (housing) is probably worn out and cracked. I had to order a front bearing assembly because the new slides wouldn't work with the worn out assembly, no big deal, it came quick. Unscrew the light bulb. Slowly pull the assembly away from the top of the front metal panel, slowly, and pay attention to where everything lines up. Replace the new front bearing and put the new slides on the little plastic tabs, be careful so you don't snap them off. Green on top, white on the sides. Replace the lightbulb. Set the front panel into place on the tabs at the bottom of the dryer. Rehook the door wires (2), and have someone hold up the drum while you slide the front bearing into the drum. Holding the front panel in place, turn the drum by hand and check for binding, things that don't sound or look right. Replace the 2 nuts to hold on the front. Plug it in, keep your hands back, turn it on, look, listen, everything fine. Open door, unplug, replace the top and the 2 screws that hold it on. Plug in, turn it on and check for any noise, you shouldn't hear any. If you do, you didn't do something right or maybe your drive pulleys are bad. A good dad and son job; especially getting on the ground and reaching under to deal with the drive belt. Watch out for sharp edges on the sheet metal and be slow and careful with the front plastic bearing so it doesn't snap. Your now good for 5 more years. A 2 on the difficulty scale, just take it slow and have an extra set of hands.

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Just took out of plastic wrapping and put on dryer. No tools needed.

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat