DU1015XTXT2 Whirlpool Dishwasher - Instructions

Long story short, noticed one of two leaks and came to conclusion there is no workaround since sump pump gasket seems to be hermetically sealed to sump pump. Which is understandable because of water in area. Wife helped by soaking other parts that were removed and replaced, because of calcium buildup. Which we hope will extend life of dishwasher. I put 1 to 2 hours because I took my time and made sure all parts fit correctly and were back in their original place. Didn't want to take any chances in not covering bases. I am no expert, but definitely a diy'er. I believed I saved myself anywhere from $200 to $300 in labor costs by repairman. By the way, thanks Parts Select your info and site are awesome!!! The second part I had to order was the water inlet valve and your phone representative was a big help over the phone, please don't eliminate those positions. Overall total price of parts approximately $130 w/delivery. Well worth it, since a brand new halfway decent dishwasher starts at $550.

Very simple just remove the rakes and then unscrew the covers and pop out the old chopper assembly and replace with the new and then just put all cover back and it works great.

I removed the upper dishrack easily by removing the end clips and sliding the tray out. Removal of the revolving sprayer was easy as it just clipped on to the bottom of the rack. The rack was not the rack that was ordered and I was informed that this was the correct rack for the dishwasher even though the description and picture was different that what I received. There were no instructions with the rack to explain how to attach the "flaps" that can go over lightweight dishes to keep them from flipping. Every way I tried to attach the flaps did not work. When I was able to attach one it would pop off if I raised the flap to place a dish underneath it. I finally gave up on the flaps and reinserted the rack onto the rails and put the end clips back in place. The rack works fine other than it is not the one that was described and was not the rack that I wanted.

The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.

Rubber friction sleeves on each side of the door provide resistance to prevent the door from quickly opening when unlatched. Over time the friction sleeve may crack and fail. Two friction sleeves are required for repair. Install a new sleeve on each side of the dishwasher door near the spring connector at the bottom.

Open dishwasher door.

Remove the screw from the left and right bracket at top of dishwasher door opening. Brackets secure the dishwasher to the countertop.

Gently pull the dishwasher forward to expose the door spring on each side of door at bottom.

Unhook the plastic spring connector from the left door spring hook by pulling the connector slightly forward and lifting from the door spring hook. Remove the old friction sleeve if still in place by sliding over the door connection hook. Discard the old sleeve.

Insert the new friction sleeve over the door spring connector hook and push until the friction sleeve is in position completely past the spring hook. Reconnect the plastic spring connector to the door hook.

Repeat for right side of door.

Close and latch the dishwasher door. Unlatch the door. The door should remain in the nearly closed position held in place by the friction sleeves.

Slide the dishwasher back to the original position under the counter top.

Insert the screws in the top brackets to secure the dishwasher.

removed and installed cords with screw driver

Disconnect power Pull out dishwasher. Turn it 45 degrees to your right. Turn it on its side. disconnect the connections to the heating element {2}. Remove bolts, remove element. Install new element and tighten bolts. Reconnect electrical connectors. puch it back in place. reconnectPower your done

Removed bottom sprayer by turning thumbscrew clockwise approximately 2 turns. Disconnected pipe that feeds upper sprayer by twisting approx. 1/4 turn in CW direction. Removed 4 screws that hold the bottom plastic plate. Removed 2 screws that hold plate on bottom of unit that also holds the choper assembly cover down. Pried off chopper assembly cover and removed broken chopper assembly and replaced with new. Reassembled all parts in reverse over described above.

The cause of the problem was that the chopper was worn out. As a result, the chopper screen was clogged with unchopped food bits. This severely reduced the amount of water getting to the circulation pump/impeller. This was what caused the spray arms not to spray. As a result of replacing the chopper, the dishwasher now works like new.

As far as how I did the repair, I followed the excellent how-to video provided by PartSelect that you can access when you click on the Chopper Assembly from the Pump and Motor Parts diagram for this dishwasher.

I didn't finish the repair because there was a wrong seal in the kit. The factory impeller kit 8193951A from Whirpool comes with a totally different seal that I took out of the washer and the schematics from their own website and the manual shows the exact same seal that I removed, but is not even close to the one I received. I am stuck with a good dishwasher that I have to junk because of a $2 seal that whirlpool won't help me with. So much for customer service.

Unscrewed brackets from underneath counter that hold dishwasher in place. Pulled dishwasher out of cabinet to access door hinges (approximately 8 to 12 inches). Released springs from door hinge (not necessary to remove spring from hole in dishwasher frame). Did not have to remove old sleeve because they tear and fall off. Slipped sleeve over door hinge to groove where they sit on hinge. Note: pulling hinge away from dishwasher a little. helps to complete installation.
Reinstall spring over hinge and check that door will stay a partial open. Slide dishwasher back in place and install screws from bracket to underside of counter.
My dishwasher only had two screws under counter to hold in place. Some installations have screws at sides also.

Very easy to remove the broken one and just clip in the new one.

Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues

Fast,smooth,easy.

Was a simple task to perform, a child could have done it. The technical skills diagnosing it was a bit hard though. The skills finding the culprit was indeed simple. Rubber was torn. Dishes would not come clean especially on the top & would not dry properly. The rubber piece being torn in half made it hard for the water & soap to despense to the top through thh center plastic tube, but now it cleans great. Thank's
Now to find out why it won't dry properly at the heating element is another task. It leaves water droplets on the dishes.
Once I got the rubber screw on attachment installed the dishes are clean & dry now & no water dropplets on the dishes.
The water dispenses up to the top like it suppost to throught the small tube to wash the upper rack dishes.
The wife is happy now she doesn't have to clean & dry them by hand.
Thank's so very much!!
Now on to the next project in hand to submit later on.