DG600EXV2 Frigidaire Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Symptoms suggested drum support bearing was problem.
Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!
Parts Used:
-
Calvin from Las Vegas, NV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench set
Was this instruction helpful to you?
Thank you for voting!
The Rear drum bearing kit had sheared off
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!
Parts Used:
-
Amy from salem, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Scraping noise at rear of drum
Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.
Parts Used:
-
Bruce from Roscoe, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Squeaky noise from rear of dryer
Unplug dryer, remove rear access cover and removed belt from pulley. Remove bottom cover on front of dryer, remove top of dryer, unplug harness to control panel and remove front door assembly. Remove screws from drum to bearing assembly. Removed drum and belt removed bearing assembly by lifting up and out of the bearing socket. Vacuumed all the lint. Removed the bearing socket, installed all parts and covers in reverse order.
Parts Used:
-
Kenneth from Pensacola, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Loud squeaking noise when running dryer
It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.
Parts Used:
-
Conrad from Schenectady, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken pulley & belt
-
Michael from Anchorage, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Squealing noise when drum would turn.
I highly recommend watching the repair video. I could stop the instructions and do the procedure then resume instructions for the next step. I would recommend you have a second person to help lift the drum up & out of the dryer frame. And ladies please instruct your husbands to watch the video all the way through. Mine lifted the top off the dryer and stuck his hand in and cut his finger immediately on a sharp piece of metal. You know because they don't need to read the instructions.
Parts Used:
-
Martha from Okc, OK
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rear bearing on dryer was squeeking badly
I followed instructions I found on u-tube to remove the drum and belt and access the bad bearing and change it. The instructions were quite good other than needing to remove a small panel on the back of the dryer to pull the belt around the tensioner.
Parts Used:
-
Douglas from Hudson Falls, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Dryer became very loud after about 15 min.
Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!
Parts Used:
-
warren from holly hill, SC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Loud squeeking and vibration of the dryer drum.
I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.
Parts Used:
-
James from Centennial, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer squeaked
It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!
Parts Used:
-
Cathleen from Port Orchard, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drum squeak
After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.
Parts Used:
-
Jeffrey from Auburn, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer started to squeal when started
I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.
Parts Used:
-
Niel from Howell, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Beaing was bad - installed new bearing
installed the back bearing with the ball bearing and dropped in the rear drum bearing and tried to install the drum to the rear drum bearing, but we could not find the screw holes to attach the drum, we tried and tried and finally I came up with the idea to take the drum out and screw the drum bearing while we had it ouside and that worked out beautifu lyl and all we had to do was reinstall the drum and all we had to do was lift it up just a little and drop it into the retainer rear retainer' and then all we had to do was install the tension roller which we had a little trouble but we finally figured it out and now it works just fine, it would a lot if there was a diasgram included on how to re-install the tensioner
Parts Used:
-
charles from kissimmee, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Old bearing made noise. Grease was dry and worn out.
The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.
Parts Used:
-
Edward from Lindenhurst, IL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!