DECIFL3 Frigidaire Dryer - Instructions

I took the dryer apart to vacuum and check because of the screaching noise. Took drum out and found the bearing in pieces and shaft had rubbed against the brace. I thought as old as my dryer was I would never get a piece to fix it. I got online and found PartSelect.com. I found the part but could not tell if all was included. there was a Phone Number so I called it. I was helped instantly. They acted like it was no big deal to have a dryer that old. I got my part within a week and had my dryer back together. It works like new. Thank you

Unplugged the dryer, removed the top of, disconnected the electrical connectors, removed the front panel, disconnected the belt, removed the drum, removed the old Safety Thermostat, installed the new Safety Thermostat and assembled the dryer again.

The repair went smoothly considering I am a rookie. The repair videos on your site are great. Followed the techs instructions and got thru it fine.

Thanks,

Jim

I followed the instillation instructions provided on your website. They were very informative and spot on. My only problem was my strength. I could not get the drum off of the rear bearing myself, but then I am a 61 year old female.

I replaced the drum kit and belt.

First I pulled up on top panel. Next I removed the two screws holding on the front panel on. Next I pulled forward and front panel pulls out. I cleaned the old upper & lower drum glide & drum seal using a razor blade. I used the high temp glue that came with the top glide. I glued them both on & let sit for about half hour. While the glued dried I installed new belt & belt idler pulley. I re-assembled the front panel while lining up the drum. Re-installed the 2 screws. Snapped the top panel back in place. Plugged it back in & turned it on. Awesome noise was gone & working great.

Popped the topped using a putty knife to free two clips in front. Remove two screws now accessible on the front inside panel. Remove two wires to door switch. Remove rear access door, two screws. Remove belt from tensioner in rear and remember or take picture of how it goes. Lift barrel slightly and pivot front panel out of the way. Lift barrel free from ball socket in rear. Lift out from front panel area. R & R kit and put back in reverse order.

Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!

removed drum & replaced bearing, belt & shaft - reassembled

i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done

Took front door off, top off, frunt off, removes screws holding rear bearing pivot, and then removed drum. repainted bearing surface on drum, installed parts, let paint dry for a day and reassembled.

Moved dryer out where I could get to all sides, then pulled top off, then unscrewed the front panel. The drum lifted out of it's ball bearing assembly in the back with a little force. Then it slid out fairly easy.

I replaced the rear bearing assembly, the bottom drum glide strip, the top drum glide and the vent seal all at the same time. The glue for the glide strips took about an hour to set up and I used clothes pins every 4-6 inches as suggested by someone else here on this site. Then I vaccuumed out the entire dryer body, vent pipes and every nook and cranny.

I put everything back as it had come out and then put the dryer back in it's place. Plugged it back in and it's as quiet as when it was new. Total time of project was about 1:45.

My husband took the front panel off. We scaped the old seals off. Used the adhesive that came with the drum glide and replaced both parts. No more ripped and stained clothes, that easy!

All I had to do was pop in the new door catch. Works perfectly.

I took the new screen out of the box. I removed the old lint screen from the dryer, and I put in the new screen. Real simple!