DE100ADV1 Westinghouse Dryer - Instructions

Margery from Hartland, ME
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

belt squeking.

Replaced belt

Parts Used:

Eugenio from Lewiston, ME
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Dryer drum would not turn.

The first part was the most difficult-opening the front of the dryer cabinet! Once open, the new belt was installed and then the new idler pulley was put in-place. The cabinet was closed-job done.

Parts Used:

Gregory from Prattsburgh, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Bearings Went and Idler Roller fell apart, not allowing drum to turn

unbolted one bolt and replaced old unit with new unit....took only a few minutes. Part was supposed to arrive in 3 days, but arrived next day....thanks very much!

Parts Used:

Dennis from Hudson, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

The dryer tub started screeching and then dropped.

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

Parts Used:

Drum Support Bearing

Gloria from Murfreesboro, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

worn bearing

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

Parts Used:

Drum Support Bearing

Mike from Midlothian, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Drum didn't turn

Removed small panel from back of Dryer,and removed Idler Pulley Assembly. From the front,lifted the top of Dryer to get access to the drum,disconnected the two wires for the Stop switch, removed the four screws, two on each side,and lowered down the front panel. Now,removed old belt and installed new, installed new Idler Pulley Assembly,aligned belt with Pulley.Reassembled the front and the top of the Dryer and I was done.The pulley was squeaking,but a shot of DW40 took care the problem.
Thanks

Domenico Intrieri

Parts Used:

Dominico from Westerly, RI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Socket set

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Control will not work - only clock blinks

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Parts Used:

Main Terminal Block Kit

Sue from Lampasas, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

0 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Dryer did not turn

put the new part on with ease took 5 min.

Parts Used:

Bryant from tolna, ND
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

18 of 646 people found this instruction helpful.

Was this instruction helpful to you?

Door latch broke

It was super easy ! The part came and I had it done in less than ten minutes. No mechanical skills necessary !

Parts Used:

Donald R from Dalton, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Door Would Not Close

Inserted clasp in frame of door

Parts Used:

Robert from Hernando, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Dryer door would not stay shut.

The other door latch broke and fell out. I simply pushed the New Door Latch in the hole, and it snapped into place.

Parts Used:

George from Bainbridge, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Dryer making lots of noise

Remove small back plate near floor with 1/4 inch nutdriver unscrewing two screws. Lay the small plate to the side. Remove dryer belt from around pulleys by pulling up on the old idle arm near main spring. This will loosen tension of the belt. Belt just needs to be removed from only around the two pulleys. Detached spring from old idle assembly. The old assembly will just lift out. Reassemble in reverse order with new assembly from Parts Select. Takes less than 5 minutes. Extremely easy!

Parts Used:

Bennie J from Kite, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

Was this instruction helpful to you?

Catch broke

My son kept slamming the door wrong and eventually the catch broke and two and feel out. My husband is the handy man of the family, but has been so busy that I was just duck tapping the door close. Finally, I decided to see if I could look up the part. Found it on here, ordered it, and replaced it all myself! Proud mother right here! Very easy. Works great.

Parts Used:

Stacy from East Nassau, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

latch assembly popped out partially on door and when it shut it broke the catch on the dryer.

Popped in new catch and used needle nose pliers to squeeze old latch flat and remove from door. New one just popped into place.

Parts Used: