DBSR463GGW General Electric Dryer - Instructions

Just slipped it on. No problems, No Tools.

Replace the front and rear bearings. When I have to do it again I will only order (3106), (313), 2x (316) green, 2x (316) white, and drive belt. Taking it apart and putting it back together was easy. Unplug the unit. Take out the 2 philips screws that hold on the top. Lift the top from the front to clear the locking tabs in the back and take it off. Take out the 2 5/16 screws that hold on the front. Tilt the front (door) forward and rest the drum on the dryer sides, you'll see it. Disconnect the wiring harness for the light and door switch, 2 wires. Lift the front off the bottom retaining clips and place aside. Have someone hold up the drum. Reach under and unhook the drive belt. Pull out the drum assembly. Take off the rear bearing, 3 screws. Clean out the heating element area in the back of the dryer while you have a chance. Replace the bearing assembly. I bought the entire bearing assembly but I could have gotten away with just the sleeve ( 3106), but I didn't know that at the time. Take off and replace the drive belt. Lock the tension arm for the drive belt into the compressed position shelf holder by the motor, push the arm down, you'll see it. Replace the drum and have someone hold it up while you rehook the drive belt and release the tension arm. Now, I would suggest replacing the entire front bearing. If the slides have been bad for a while, the plastic bearing (housing) is probably worn out and cracked. I had to order a front bearing assembly because the new slides wouldn't work with the worn out assembly, no big deal, it came quick. Unscrew the light bulb. Slowly pull the assembly away from the top of the front metal panel, slowly, and pay attention to where everything lines up. Replace the new front bearing and put the new slides on the little plastic tabs, be careful so you don't snap them off. Green on top, white on the sides. Replace the lightbulb. Set the front panel into place on the tabs at the bottom of the dryer. Rehook the door wires (2), and have someone hold up the drum while you slide the front bearing into the drum. Holding the front panel in place, turn the drum by hand and check for binding, things that don't sound or look right. Replace the 2 nuts to hold on the front. Plug it in, keep your hands back, turn it on, look, listen, everything fine. Open door, unplug, replace the top and the 2 screws that hold it on. Plug in, turn it on and check for any noise, you shouldn't hear any. If you do, you didn't do something right or maybe your drive pulleys are bad. A good dad and son job; especially getting on the ground and reaching under to deal with the drive belt. Watch out for sharp edges on the sheet metal and be slow and careful with the front plastic bearing so it doesn't snap. Your now good for 5 more years. A 2 on the difficulty scale, just take it slow and have an extra set of hands.

The inner piece of the knob cracked so it just spun on the dryer shaft it's suppose to turn. Ordered a new knob, slipped it on and all works great again now.

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Just took out of plastic wrapping and put on dryer. No tools needed.

Pulled off old knob and snapped new one into place. Took about 5 seconds. Must be a lame design cause my dryer's less than 2 years old and the knob snapped on the inside and wouldn't turn. Easy to fix though.

I was using vice grips to turn the control knob (stub) until the new knob arrived. The replacement knob was a redesigned type with a metal backing plate to place on the control knob stub (better than the original plastic knob) however the diameter of the new knob is only half the size of the original knob and the mark on the dial does not line up with the markings on the dryer control panel making it difficult to know what cycle you are using or how far to turn the dial within each cycle before passing to the next cycle.

i follow your video and all went well except now the dryer will not heat. i went back on your site an tried the no heat option an still no heat

Removed that to screws for that top first and door shake top little to that front and I took two screws on that top each side and removed that front and lint trap and install the new

remove the broken one and replace it with the new one

Opened dryer door and removed two screws that held front of top panel on. Lifted top panel off and removed two screws that held front panel to side panels. Tipped front panel forward and replaced all four slides. Cleaned everything off and put back together. Works great again. Thanks for this site and for others that have done these repairs before and posted their stories.

Son found out where the bulb was by using YouTube. I googled lamp for model number and your website came up. I ordered the part, it arrived promptly, and my son installed it.

The timer knob was sent, but the part on the dryer that was broken was a different knob. We were able to use the knob, but it was much bigger than the old knob.

I believe the diagram for the dryer showed the timer knob, but not the three other knobs.

I wish we would have received the correct knob, but the supplied knob is working for us.

Pull the two scews to release the top of the cabinet. Pull the two screws to release the face of the cabinet and tilt out.
Take the old slide out and install the new ones.
Put it back together.
No more squeeks
My wife thinks I'm a genius...

I followed the very easy YouTube video and got the three tools I needed before beginning. I started with removing the parts of the dryer and that was extremely simple by following the steps in the video. Took the door off last, located the parts that need replaced that didn't require any tools at all. Then put all the parts of the dryer back on in the order I removed them. The entire process was about 25 minutes but I would say I spent more time really cleaning the dryer and lint build up than actually doing the repair. Video was super thorough and easy to follow, I've never attempted any kind of repair of an appliance and I'm extremely happy that I had the video and the parts that were recommended to fix my problem, were spot on. Saved me hundreds of dollars and time. Thank you so much!