DBSR453EB1CC General Electric Dryer - Instructions

took off top of dryer, took out 2 screws so front of dryer could be removed, replaced bearing,slides and felt seal

Took the front & top off the dryer. Saw that the slides were missing or broken. Got the parts and put it back together. Works great.

Took the top of the dryer off by removing two philips screws in front. Removed two screws holding the front of the dryer on. Pulled the front out enough to reveal the worn drum slides. Replaced them. Reassembled.

i first popped off the top of te dryer after removing the two screws in frotn when you open the door. I then removed the two screws holding the front together. after tilting the front out i was able to place the slides in without having to pull of the front entirely.

Repair was VERY easy - 4 screws total! Used google to find a video online that showed the steps.

r/r parts unit runs great

I ordered and replaced the front and rear bearings, including the slides that go on the front bearing. Most of this was un-necessary; replacing the slides would have been sufficient, and much easier to do. Two of the old slides were worn completely away.

I simply removed the switch and matched the pole numbers to the new switch eventhough the new switch had two extra poles. The switch replacement was straightforward and worked very well.

Before removing the old part,took photo with my phone camera to document the color wires hook up. Screwed in the new part and hooked up the color coded wires using the photo as reference. I was surprised how easy it was. Thanks. Partselect gave me fast shipping, cheap price and great customer service.

Followed the Part Select video instructions which made the repair really easy!! Thanks for a job well done! ALSO.. the drum wobble was not caused by worn slides and felt. There are three screws holding the drum axle flange. Two of them fell out leaving the drum to flop about as it rotated. So we scavenged some screws from elsewhere on the dryer and problem solved. Once again.. thanks to Part Select for great instructional videos and great customer service ordering parts.

Replaced drum bearing part and white slides.The problem was that it was not the drum slide support. It appears to be the the drum rear bearing of whch I am now ordering. The bearing replacement is a little more difficult, but I have taken this on as a challenge

It was as easy as the repair film said it was . But after spending the money for the upper and lower baring seals I put it all back together and the motor started making a loud noise ? I took the drum and everything out and started the motor without the drum just the motor was running and the danged motor is going out now !I checked the price of a new motor its not to bad but with all of the parts I have put in this thing I could have paid part of what it would have cost for a new dryer ! I put it all back together and hope it last long enough to at least recoup some of what I have spent ,But the new parts work good !

1) Disconnect power supply. 2) Open dryer door to find and remove two screws through dryer top. 3) Proceed to lift front dryer top panel and tap rear of dryer top with hand to left to disengage tabs and remove dryer top completely. 4) Remove two screws through front panel. 5) Gently lift dryer front panel from base tabs to partial remove panel (careful of wires which remain connected) - pivot front panel to left with wires connected. 6) lift dryer barrel with left hand / reach under barrel with right hand to release belt from tensioner pulley (very easy one-hand maneuver). pull dryer barrel belt off tensioner pulley towards you, remove belt from motor pulley below. 7) lift/pull and remove dryer barrel and belt (flex side panels). 8) take picture of wire connection locations on heating element and remove wires from tabs two locations / 3 wires. 9) remove sensors 3 locations. 10) remove heating element and housing. 11) install new heating element / housing and reverse process. .....tip; belt tensioner pulley was biggest challenge at first because it was hard to see how it all worked and reach. once i realized i could force / lift the barrel up to gain better access it was much easier than trying to fit my arm through the one large available hole at bottom right (when looking at the unit). the tensioner pulley is opposite side (left when facing) and you would have to reach over the exhaust, etc.

remove front and top cannover's from dryer.remove plastic inside bearing housing and plastic bearing slides replace worn out bearing slides with new ones. needed 4 bearings direction suggested only two....

Faulty Door switch. Dryer would heat up so I knew it wasn't thermostat or element related.