All Installation Instructions for General Electric Dryer DBSR453EB0CC

Rubbing noise while dryer was running

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Carol from Simpsonville, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Loud squeek when dryer was running

Take out the two screws holding the top on with the door open remove top and remove two small screws in top front corners. I replaced the 4 slides and the drum bearing without the new felt, do not do this it continued to squeek after it ran the first few times when i got the new felt a week later i installed it in ten minuites and the noise is gone. I think it cost around sixty dollars and my dryer is back in action. Make sure that you clean all of the lint out of the inside of your dryer I had alot of build up near the chute for the lint trap.

Parts Used:

DRYER BEARING SLIDE GREEN 2PK

Clarke from Grapevine, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

door handle broke to dr;yer

handle broke on sunday( not the best day to order things). ordered it from this site and had it by tuesday. great service and best price i found on the web. tks

Parts Used:

Dryer Door Handle

ROBERT from MONROE TOWNSHIP, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

My dryer wouldn't start, I saw the part on your website after reading comments from other people

I put the nob on the post, one side is flat the rest of the lever on the dryer is round. So I matched up the lever with he inside of the new knob and slid it on . The dryer works perfectly. I ordered it on May 5 th and the nob arrived May 15 th. I guess Georgia is a long way from Arizona. But the part fit perfectly and I am happy. Thankyou.

Parts Used:

Knob and Clip

Margaret from SCOTTSDALE, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The Start knob broke off

At first the knob seemed like it would not fit on, but after I sprayed it with WD-40 oil, it slipped with a gentle, steady push

Parts Used:

Knob and Clip

Sally from MANHATTAN, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Burnt out bulb

Used a flash light to see, reached in and installed new bulb above the door

Parts Used:

Light Bulb

Jeffry from ROCKVILLE, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Bulb

Open dryer door, reach in at the 12 o'clock postion
on the inside is the bulb.

Parts Used:

Light Bulb

Mark from Monroe Township, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

light bulb dead

remove the old one and put the new one...!!! Easy

Parts Used:

Light Bulb

Carole from Wynnewood, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

On knob went bad

Took new one out of package, and push it on. 4 seconds!

Parts Used:

Knob and Clip

Bruce from ELVASTON, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Bulb was intermittently working

Inspected door switch operation and was working properly and simply looked for bulb in the dryer drum housing and located it immediately above the door opening,unscrewed it and noticed the broken elements inside. The bulb is a 10w/120V. Installed bulb problem solved.

Parts Used:

Light Bulb

Peter from LEOMINSTER, MA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Broken knob and could not turn on dryer

followed the video you provided and it was easy!

Parts Used:

Knob and Clip

James from YARDLEY, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

broken start knob

Just push knob on less than 4 seconds

Parts Used:

Knob and Clip

Bruce from MONROEVILLE, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

My last phase of repairs of minor items.

if your unit has over 6,000 hours of operations, one needs to remove the front panel and inspect the sliders that the drum rides on. The video were very helpful to replace the sliders. Unfortunately, my dryer had over 10,000 hours of operations over a 30 years period, hence a major repair costing over $200.00 dollars. The drum sliders were gone, hence the drum eat through the plastic guides. More so, the drum started to eat away the front panel. If the dryer is eating your closes and making a noise, one is looking at a $200.00 repair job. Hence check the sliders early will save one $$$$.

Parts Used: