CWG3600AAS13 Maytag Wall Oven - Instructions

Screwed in light bulb and glass protector

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.

Replaced gas oven ignitor

We took the interior floor out, pulled the stove away from counter, before that turned all electricity to the house off. Then we unscrewed the ignitor inside then underneath unplugged it and plugged in the new one, cleaned to oven and screwed the ignitor in and replaced the interior floor and we were done.

My oven would not work. It took longer & longer to fire, finally died. I did an online search & found partselect.com, with it's very helpful troubleshooting info, and somebody posted info that 80-90% of the time it's the ignitor that has failed. I ordered it Sunday night, it arrived Tuesday. I took the door off for easy access, took the bottom of the oven out, removed the flame shield and replaced the ignitor. I tested it and it worked! The hardest part was moving the stove away from the wall & threading the ignitor plug thru the back of the oven. The cheapest appliance repair visit would have been $89 + cost of parts. Sears charges $129. I think I saved at least $100, thanks to partselect.com.

This website easily diagnosed the probable problem. We ordered the suggested part and my husband replaced it, despite a slightly eroded, rusted screw that was stubborn to remove, in about 20 minutes. The oven is working perfectly. With tax we spent about 50 bucks. I was sure we needed a new oven. We, ironically, celebrated by going out to dinner!

removed the old defective ingniter and installed new igniter turned on the ove n and wala, it was like brand new.

I opend the bottom cover, which had for screws then , opened 2 screws that atached the igniter to the main gas pipe and pulled the whole wiring out and disconected the wiring , ordered the igniter two days later, I put the whole thing together in less than 5 minutes . put back the cover. and I tried it , everything was cool , accutaly hot and working .

We hired the neighborhood handy man, and he was able to repair the oven in about 15 minutes. I order the part and received it the next day. Excellent Service!!

My stove would take forever to preheat and sometimes it wouldn't heat above 175. I order a new igniter, which was located under the drip pan . It took less then ten mins to replace and the stove is working like new.

Changed the igniter

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Once I got the new Igniter, I unplugged the old igniter and took two bolts out. Then remounted the new igniter and plugged it in. Works like a charm!!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.