Quick Question!

Have you ever purchased from PartSelect.com before?

Models > CWEF322ES5 > Instructions

CWEF322ES5 Westinghouse Range - Instructions

All installation instructions for CWEF322ES5 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the CWEF322ES5
16-30 of 67
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Element had burned out

  • Customer: John from Pearland, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 7 people found this instruction helpful
Extremely easy. Two screws and electric connection that had easy pop on-off connection.

Electric Oven - No Heat in the bake Mode.

  • Customer: Rodney from Orange Park, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Broil worked on the stove, however in bake mode, the oven did not make temperature. Turned off the stove, unscrewed and inspected coil. I noted there was a section of the coil that had a "corroded" appearance. (it was evidence of the coil being burned out). Checked with a ($9.00) voltmeter, showed infinite resistance. Found the original envelop for the stove taped to the back of the oven from 1973. It has wiring diagram with schematic and noted the coil was 3000 W, 19 ohms.

Bottom Line found comparable replacement online and tested resistance, measure dimensions of the old coil, matched with Watt rating, replaced, tested installed and works great, Oven has been in use for a couple weeks now. New stove would have been around $500.00. Not to mention some remodel work, as the house is old and stove is a built in.

Coil was $60.00 and should buy the time I need until I remodel the entire kitchen.

Bake element stopped working

  • Customer: Stephen from ROCHESTER, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
1. SHUT OFF POWER TO YOUR RANGE! (I flipped the circuit breaker at the box to do this. To be totally safe, you can shut off the power to the whole house.) 2. Remove the oven racks. 3. Undo the two screws (save for step 8) holding the bake element in place. (This took some doing for me, as the screws did not want to come out easily. Maybe use some penetrating oil and be careful not to strip the screws.) 4. Gently pull the bake element toward you, exposing the contacts and wires. 5. Remove the wires from the old element's contacts. (Remember which contact 6. Attach the wires to the new element's contacts. 7. CAREFULLY push the wires back into the wall of the oven. (Pay attention to the insulation. Make sure that some insulation is near the wall.) 8. Fasten element to wall of oven with screws you saved from step 2.

Bake element was cracked

  • Customer: Alan from ROCHESTER, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.

Bake element burned out

  • Customer: Sylvia from Escondido, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Took out the bad element and replaced it with the new element in less than 5 minutes, worked perfect, thanks

Baking element not working

  • Customer: Larry from Houston, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Bottom oven quit heating about 6 mos. ago and now top oven quit. Broiler worked fine on both. Bought 1 replacement element to try. Did not work on either oven. Found online where someone had found a bad solder joint on a relay board so I pulled the oven and removed the covers. (WITH POWER OFF. I made a diagram of the wire connections to the board and removed it. I FOUND a cold solder joint on the L2 connection of the top oven board. I found the exact same cold solder joint on the bottom oven board also. After resoldering the connections and touching up any suspect joints I replaced the boards. They BOTH WORKED fine!
Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.

The original element in the oven burned up one evening

  • Customer: Gwyn from Boulder, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
We pulled the stove out from its slot in our island. We unplugged it and unhooked the gas line so we could get behind it easily. We then took off the back (using screwdriver) to get to the connectors for the element. We unhooked the connectors from the old element. Then we took off the plate inside the back of the oven (using screwdriver)and gently pulled the old element out. We seated the new element in the oven and then hooked it up in the back and put it all back together again. It worked perfectly! The hardest part was cleaning the dirty floor under where the oven had been for 7 years!

oven wouldn't work

  • Customer: david from olney, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
It's kind of embarrassing!
As the breaker was being thrown to turn the current off, I discovered that the breaker box was burn up at the breakers.
Short story but I got'er done! The problem now is there is something still wrong with teh oven!
I think I see a new one in the future!
Thank you very much for the very prompt delivery.
My purchase has been without a flaw.
I have already sent the part back for a refund.
It cost me something like $13 for this experience for freight.
I will remember you with my next need.

bottom oven element not heating

  • Customer: dempsey from eastland, TX
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 116 of 369 people found this instruction helpful
replaced bottom oven element, did not fix the problem. replaced the thermostate and the terminal block and that did not fix the problem. parts select what is next?

Heating element burned out

  • Customer: Jack from Hedgesville, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took screws loose, unplugged old one plugged in new one put screws back

Oven would not heat after running self clean

  • Customer: Michael from Owasso, OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Googled the problem and found Oven Temperature Sensor and Main Terminal Block to be the most likely problems. Turned out to be neither. No parts were needed. Oven has a thermal overload switch on the rear upper left. Thermal overload needed re-set. To do so you have to remove the oven, remove the back and press the red button on thermal overload. Biggest challenge was figuring out how to remove the oven. Even with the installation manual it was not easy to fgure out. The instructions are misleading. You need a special tool. I used two hacksaw blades as a substitute, and slid them in to release the clips. Once you figure out how to get the oven out the rest is simple.

Control will not work - only clock blinks

  • Customer: Sue from Lampasas, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Improper temperature when baking.

  • Customer: Lorenza from Rowlesburg, WV
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Element burned out in 15 months

  • Customer: James from Basking Ridge, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very simple, just removed three screws and pulled the top out and turned over and then removed the two screws holding the support bar. Removed and installed the element.Surprised to see that the element burned out in such a short time.

Error Code F1

  • Customer: Jon from Little Silver, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first
All Instructions for the CWEF322ES5
16-30 of 67