CSX22BCBGWH Hotpoint Refrigerator - Instructions

Unplugged refrigerator and turned off water valve at wall. Removed the entire back, lower cardboard panel (turns out I didn't have to do this...could have just removed the screws from the right side and folded the cardboard along a perforated line designed for that purpose). Removed screw holding water control valve to back of refrigerator. Took new control valve, and slipped on adaptors for electrical connectors (in bag) to the two smaller of the four electrical prongs). Removed electrical sockets from old connector and placed them over appropriate prongs on new connector. Unscrewed the two old water out lines, cut the old fittings off and slipped the lines snugly into the new outlet valve (new valve had slip on connectors not requiring lines to be screwed in). Keep straight which line goes to which outlet port! Then removed water line going into old fitting and screwed it on to new valve inlet fitting (after removing black plastic protective cap). Turned wall water valve on, checked for leaks (none), and plugged refrigerator back in. Water restored to both icemaker and water dispenser!

By the way, the first valve came damaged, but one phone call and the people at Part Select promptly sent out a replacement which I had the very next day (and this was two days before Christmas!). Great job!

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.

I called the repair tech who obviously did not want to come out, thank god. He told me to remove the back panel of the freezer and also check fan on back side. Told him there was alot of ice on freezer condenser and he advised that defrost heater was probably shot, and referred me to partselect.com. I unplugged the frig/freezerer, and removed the heater and saw it was blackened and cooked. I used a hairdryer to thaw the condenser, and the new part arrived the next day. I reattached the 2 plugs, 2 screws, and put the back panel of the freezer back on. I plugged the appliance back in, checked it 6 hours later and the frig is cold again. It was a VERY easy repair and took less than 30 minutes from start to finish. I was quoted between $40-$78 for the part at 3 different places in the phone book, which would have also required a 45 minute drive. I got it here for $38 including shipping and it arrived in 24 hours !
With the "blow-up view" appliance feature on this web-site, and simply being guided to the correct part by entering the model number, it was a very easy ordering process and repair.

This is such an easy fix!
1-Unplugging the fridge and emptyi it. Remove all shelves.
2-remove the 2 screws at the top of the back panel with a 1/4 inch nutdriver. You'll have to tilt ithis panel forward and sideways to get it out.
3- DO NOT CHIP AT THR ICE COVERING THE COOLING COILS? Replace one shelf and rest a hair dryer on low heat on the shelf.. Plug the drain hole at the bottom with a rag so all the melted ice water doesn't flood the floor under the fridge. Soak up the water with a rag and bucket- this should take 20-30 minutes.
4-Remove the red and blue power cables from the element. Only 2 philips head screws hold the defrosting element in place. Once it's out you can tell it's burned out because it looks black like a burned out lightbulb.
4-Plug in the red and blue power cables to the new unit. You will need to reroute the blue power cable because the new unit has both power connections on the same end.
5-Replace the cover panel by sliding it in at an angle and replace the 1/4 inch screws.
6-Replace the shelves and plug in the fridge.
That's it!

The most difficult part of the repair was the melting of the ice and preparation. I did change a single element heater for a dual element heater, which required a little manual flexing of the sub-frame, but it assembled with little issue. I was lucky, I did not have to splice the extended harness connection. Rerouting my existing gave sufficent length.
Not sure if the single elements were changed for dual, but it did have the same PN as the unit I replaced.

Removed shelves and storage drawer from freezer.

Removed the two screws that mount the rear panel cover at the back of the freezer
compartment. Disconnected the grounding clip on the cover exposing the evaporator coils and the defrosting heater at the bottom.

Removed the remaining ice chunks on the coils.

Removed the two screws mounting the single element defroster. Disconnected the wires on each end of the defroster.

The replacement defroster was a two element heater and the instructions clearly showed how to re-route the single wire from the left side to the right side. The harness kit included a short piece of wire and a crimp connector to ensure the length would be sufficient to connect the new heater.

The only item missing in the kit was the RTV required to water proof the wire connection. A quick run to the hardware store took care of that.

Reassembled in reverse order, plugged the refrigerator back in and by the next day temperatures were normal in both the freezer and refrigerator compartment.

A service repairman had quoted $60.00 for the defrost heater plus $250.00 for installation. Using parts from PartSelect the total cost was $44.00 including shipping and about 30 minutes of my time. I'll take the savings anyday.

Thanks for the easy to read instructions and multiple status email notes of the order.

I Took the six screws off the back panel to get to underneath the refridgerator. took the 2 screws out of the bracket thast holds on the water valve took the 2 lines off and then put everything back

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.Threw away the old defroster. Put the new one in. I had to reroute the blue wire over to the right hand side and plugged it in.Put the back on. put the shelves in and I was done! We had this done just about 3 years ago and it cost us about $175. The cost of this repair was only $38.05 with shipping and all! What a great deal! Thanks so much PartSelect!

My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!

I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You'll have to drill out a rivet on bottom hinge but it will save over $30.00.

The repair itself is super easy. The heater harness comes with instructions that is easy to follow. The only issue I encountered is that my refrigerator had 1 heating element and you will get one with 2 heating elements. Because of this, the new connectors are on 1 side. Since my old heater had 1 connector on each end, 1 wire is too short if you route both wires the same way as before. The kit comes with an extra wire and directs you to splice the short wire and attach the extra wire with the included connector. I figured a refrigerator with a spliced wire is not a good combination so I rerouted the short wire to the other side along with the other wire. This allowed me to connect both wires without using the extra wire.

Removed shelves and light bulb cover. Then removed the two screws that hold the back wall of freezer compartment in place and removed cover. Thawed ice jam with hair dryer. Removed the two screws holding heating element in place and pulled element out far enough to disconnect the two wires. Reconnected wires to new element and put everything back together.
Installation instructions which came with new part were accurate and very easy to understand.
It took about 30 minutes total.

I had done this repair almost exactly 2 years ago. I also read in this forum about a guy who said he had to do it every 2 years... bad part design.

However, GE has replaced the original single element with a dual element, and that is what PartSelect sent me. I had to splice one wire, but the instructions were clear and it went like a breeze. Oh, and the part arrived less than 3 days after I ordered it with standard shipping. Way to go, guys! Thanks!

Fortunately while my refirgerator was still under warrant I had this same problem and watched the repairman fix it. To confrm my suspicions I cleaned out the freezer compartment, removed the back panel (2 screws), and used a hair dryer to defrost it. I suggest plugging the drain hole or laying a towel in the bottom of the compartment to catch the run off or your drain pan could over low. Once defrosted I was able to verify that the element on the defrost heater was burnt. Since it was Sunday I re-assembled and cranked it back up until I could get the part. I did a goggle search on Monday, found the part instantly using only the model number from the refrigerator at PartsSelect.com. The part arrived Wednesday as promised, I repeated the process from Sunday, removed the defective part (2 screws & 2 plug in type wire connections) and she works like a charm now. I do think the manufacture of the part should consider a new design since this is the second one my unit has needed in less than 5 years. At only $27.50 ea. I should have purchased a spare to have for the next time!

Very quick and easy repair. Took off cover to access valve using standardr screw driver. After shutting off water supply to valve disconnected copper water supply line. Used a large towel to catch any residual water in line. Removed two water lines on valve use plies if more than hand tight to loosen. Removed screw holding valve in place, removed valve and disconnected wires (be sure power to frig is off least you get a shock. Reverse proceedure to install new valve. new valve has simple push in connections for plastic water lines. Install two electrical adpaters and electric lines. Mount valve with screw, connect copper water line. Turn water back on and check for leaks. Turn power on and check for proper water running at dispenser. Again check for any leaks. No leaks, install cover and you are done.