CGS1230ADT Magic Chef Range - Instructions

removed the old defective ingniter and installed new igniter turned on the ove n and wala, it was like brand new.

i ordered the part, it came in speedy quick,and it was very easy to install i saved $200 bucks, and my mom was the happiest person in the world. thank you.

The repairs was easy,once I found the problem I turned the gas off and unplug the power supply cord. For the oven gas valve I used a 5/8 wrench to take the gas supply line away from the side of the valve inside the over. I used a 1/4 nutdriver to remove the two screw holding the braket down over the valve. For the glow-bar I donnected the power supply plug and used a 1/4 nutdriver to remove two screw holding it in place next to the brun.

followed instructions from repair manual.

I was sure my problem was due to a gas ingiter that was no longer working. I read about others that had the same problem as I did. I ordered the part from Partselect because they had a 30 day no hassle parts return policy.
I removed the oven racks and 4 screws to get to the igniter.
I unpluged the igniter, put the new one in, and replaced the racks. Very simple and easy to do.

I started with pulling the base of the oven to examine the mechanism underneath. The hardest part of the whole thing was working the wire connection past the metal back of the oven. It required prying the metal away from the frame rail and wedging the wire connection through. Other than that it was unplugging the old, plugging in the new, and a few screws to reattach the igniter, heat sheilds, and oven base.

He took out the bottom of the oven floor...came out easy ..had to unplug the old part and installed the new one the same way.He did have to unscrew two pieces. The only difficult part was reaching to plug in. Not too bad. Now he could do it quick and easier. Problably 10 minutes the most. Stove works great and I can cook again. Makes me happy.Thanks for all your help.

Tested power coming into unit,then tested power going to igniter,both of which were good.Did a continuity check of igniter element and found it to be bad.Ordered one from PartSelect,recieved it in minimum time,removed the old one,installed the new one,works like a champ.

After reading how others replaced their defective Gas Oven Igniter, I decided to attempt the project. My only mistake was Removing the Oven Door. Though it came off with ease, it was a complete bear to put back on.
Once I removed the oven door, I located the two phillips head screws that held the bottom oven floor in place. One screw came off without much effort, however the other stripped and had to be drilled out.
After removing the oven floor plate, I quickly located the Igniter and using a nut driver, unscrewed it. One of the two screws stripped on me and had to be replaced. The new part was put in position and the process was reversed. This is where I encounted a problem.
After repeated attempts, I soon found that the oven door hindges had to be held in the open position with a flat head screwdriver in order to be put in place. I found no instructions or info on how to complete this process (even from Maytag) and only completed the tast by trial and error. I highly suggest NOT REMOVING THE OVEN DOOR to complete the repair. The repair itself is rather simple even with stripped screws.

Checked troubleshooting guide on website / ordered part / replaced part by removing two screws in oven on bottom pan/ removed inside oven bottom for easiy access/ removed two screws from bracket holding down the heating element/separated the electrical plug in back releasing the wires to heating element/ installed the new element with two screws / connected the electrical plug/ installed the bottom panel inside oven / installed two screws inside oven on bottom panel. Checked operation of unit- gas lit ok - pushbutton panel did not increase heat seting properly/ dismantled the control panel / dismanteled the circuit board / found remains of several roaches inside circuit board recess/ cleaned all pushbutton points and re-assembled unit - all worked fine except when oven burner went off - the gas valve would not shut off completely - leaving a small flame burning at the gaaas valve orifice "DANGEROUS". I checked troubleshooting guide again / ordered a new valve - installed - (did not come with a new Propane orifice ) - had to use old one ( should have either asked me or just sent one when I ordered) - received new valve - installed with old Propane orifice - all works well now.

Removed the old igniter, followed the wires. Reversed the process and put it back together. Saved big bucks! Thanks for the quick service.

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.

I removed the cover protecting the igniter. I pulled the stove away from the wall to get at the connect for the igniter. I loosened the 2 screws which held the igniter.
Took the new igniter ran the wire to the back to the connection and mounted the igniter with the 2 screws. Turned on the oven to make sure it works and it did. Turned off the oven, replace the cover and pushed the stove back in place. No big Deal!
Your web site was very helpful. Thank you so much!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.
Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole
behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.

snaped them into oven cavity attached temp bulb job complete