All Installation Instructions for Frigidaire Range CFGF366DCG

light bilb went out

replaced it

Parts Used:

Light Bulb

Denise from Landover, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

temp was not reading right

remove back panel took out old part splice wire replaced

Parts Used:

Oven Temperature Sensor

santa from glassboro, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

3 of 10 people found this instruction helpful.

Was this instruction helpful to you?

Knob lost middle metal clamp

Received part very next day and put new knob on. Matches perfectly.

Parts Used:

Top Burner Knob

Holly from Tampa, FL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Lens cover for oven light broke.

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.

Parts Used:

LENS

Amy from Corona, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Two of theTop gas burners would not spark

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

Parts Used:

MODULE

Robert R from Lewistown, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

0 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken globe in oven and burnt out light bulb

Easy as 1-2-3

Parts Used:

LENS

Light Bulb

Sharon from Foley, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

0 of 5 people found this instruction helpful.

Was this instruction helpful to you?

oven would not stay on

remove belly pan ,pull draw out easy acsess remove screws and replace

Parts Used:

IGNITOR,BAKE

Mark from AuGres, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Needed to install an anti-tip bracket on my stove.

Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!

Parts Used:

Anti-Tip Kit

Daniel from Provo, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

Was this instruction helpful to you?

burner would not light

We took off all of the bolts holding the burner assembly's in place . Then took the top of the s range off. Used a wrench to remove the old assembly and re-placed it with the new one. It took longer to get all of the top and under cover off then to put the new part in. Very good service from Part Select. MATT

Parts Used:

Front Burner Igniter/Orifice Assembly

Matthew from Gladwin, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Wrench set

Was this instruction helpful to you?

Temperature not correct.

Pull out stove. Unplug power. Remove four screws on each corner and loosen one screw in the middle. Remove back panel. Locate and unplug sensor connector. Remove one screw from sensor plate. Turn the sensor 45 degrees and pull sensor out from the rear. Connector received had the incorrect plug and terminals so it was necessaary to splice the connector from the one removed to the one received. Cut and splice wires as necessary. Install sensor, install back panel, plug in electrical power, push stove back into position. I used a temperature gauge to check temperature after stove was in position. In my case the temperature had to be adjusted which is a keyboard function on this unit.

Parts Used:

Oven Temperature Sensor

David C from Huntington Beach, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

Was this instruction helpful to you?

inner oven door glass broken

I was unable to loosen the screws myself so I called my friends husband to help me. We watched the video together and followed the instructions. The door in the video was a bit different than mine but this repair was easy.

Parts Used:

GLASS

Cheryl from Derby, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

bought a used gas range i have propane it was natural gas

changed the orfices with a 10mm socket and driver handle used an adjustable wrench to tighten the orfice in the bottom of the oven approximately 45 minutes we were using the range

Parts Used:

LP Conversion Kit

Vernon from Moorehead, KY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

Was this instruction helpful to you?

Door glass cracked

Really straightforward - just took door off of the hinges and worked taking it apart until I got to the front glass that was cracked. Took it out and put the new piece in and reversed the process. Really easy and I got to clean each piece on the way back in to get rid of some spills.

Parts Used:

GLASS

Mike from Collegeville, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set

Was this instruction helpful to you?

inner glass door was broken

removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range

Parts Used:

GLASS