CFEF3012LWD Frigidaire Range - Instructions

The repair went relatively easy especially after reading that another homeowner found the door to be "spring loaded". I was prepared and made sure I held onto things tightly.I removed the screws as I came to them and carefully removed the other 3 pieces of glass, finally reaching the inner panel. Putting that in and holding it as I put the next piece back was the most difficult. Once that was in place, the rest was just a matter of redoing what I undid. Needless to say, I was a bit nervous the first time I used the oven. No problems though, works like a charm! Thanks!

First of all I would like to comment on how it easy it was to place this order and I was pleasantly surprised that it was rec'd the next day. Also it was the correct part that I needed. To install it, first I removed the screws and then the metal that was holding the broken glass. Once the broken glass was removed, I set the new glass in the metal strips and basically screwed it back together. Please note to be careful to remember which screws go where as they are not the same size and do not fit anywhere but where they belong. That was the only part of the job that I had a problem with.

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

The light apparatus was loose behind the panel. Remove the remaining part of the lens. Install the new lens from the outside of the panel and hold it in position, protruding into the inside of the panel. Slide the light apparatus onto the lens from the inside, allowing the bracket to hold it in place - it will be spring loaded, which will hold it in place.

removed the old burner and put the new one in it's place.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

I took the brads that were left from the old gasket off with needle nose pliers. Then I put the new one on. It was very easy.

I had already switched off the breaker for the range, so I unplugged the unit and moved it out from the wall. I removed the screws on the rear cover and exposed the clock/timer. I then removed the four screws holding the clock/timer,used my pocket knife to gently pry the wires off of the old unit one at a time, as these were very tight. Holding the new clock/timer in my other hand I installed the wires one at a time to match the original clock timer wiring.I installed the clock/timer, the range back cover, slid the range back into place, plugged it in and turned on the breaker. My wife is happy, I am too.
A repair shop wanted $100.00 just to go to our home and look at our range. We spent $104.00 plus $20.00 for the new overlay, fifteen minutes of my time, a real bargin!
Thank you PartSelect, I'll be ordering from you again!

made a drawing as to where the wires were to placed on the new switch,took longer to do this than finding right tools. Important safety tip,always pull off the required breaker!!!

I couldn't unscrew the leveling foot because it was rusted and corroded. The bracket holding it was easy to remove so I took the bracket with the corroded foot off and replaced it with the new foot and bracket. Very simple. I made sure I oiled it so it wouldn't rust again.

first i remove cover, then i unscrew defective part, remove wires. i then install new part & replace marked wires . I then replace cover, turn on oven and holla! my oven is working.

Discovered that that oven control panel was to blame for both heating elements to stop working at the same time. Went online and ordered the part which was delivered in 2 days. Installation very basic and included the following: 1)Pulled out stove and un-plugged stove 2)Removed top rear panel 3) Removed 4 screws of the damaged control panel (leaving all wires plugged in) 4)Installed new control panel and connected wires one by one to make sure done correctly 5) Replaced rear panel plugged in stove testing oven.

It went very well. Very quick. Just took out a couple of screws, took out the rest of the broken glass, slipped the new piece in and screwed it all back together. This was the first time I had ever tried to fix any part of a range/oven before, it was very simple...

Watch video. This oven had the connecters that popped off and on which made this task easy.

The elements tested good. Figured it was the electronic clock timer/control using the sites repair guidance and ordered the part. The remove and replace was very easy. Pulled the stove out, removed back panel and removal and replacement of the part is pretty basic. Be sure and unplug the appliance first. Everything works fine now.