Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water Leaking
Simply remove the washer nut,then pull the float assembly. As far the lever,just unscrew the screw and replace the actuator lever. What was great about everything I was able to go to the presented diagram. This allowed me to find the exact parts I needed. Of course make sure you have the model number.
removed spray head, pulled motor/pump assembly. took apart impeller housing and then removed motor and pulled impeller off its shaft, the most difficult part was actually pulling off impeller from the splined shaft. I actually broke old impeller in the process. The good thing is that the new seal came assembled with new impeller so that was not a problem. After re-assembling everything it worked fine and still works for a week since repair.
Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
7 of 8 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leak from Bottom of Float Assembly
Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.
Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.
Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed. Super fast shipping on items!! Great service.
Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.
Dealer phone quote = $250. DIY repair = $55. Turn-off DW electrical circuit breaker and shut-off hot water supply. Remove lower Front Access Panel and Toe Panel. Disconnect hot water supply, corrugated drain hose, electrical connection, and uncounter mounting brackets. Slide-out DW (being careful not to scratch flooring) and gently tip DW onto its back side. Rotate Ring-Lock at underside of Tub and (from inside the Tub) carefully lift out Motor-and-Pump assembly. At the Motor-and-Pump assembly, unscrew Center Spray Nozzle and remove Lower Spray Arm and lv Filter. At the end of the Impeller, remove Chopper Screw, Chopper, Chopper Plate (rotate 1/4 turn) and Chopper Wear Ring. Remove Motor Mount Screws and Motor Shield. Loosen Impeller {NOTE: left-hand thread} from motor shaft by the holding Motor Fan stationary and unscrewing Impeller. Pull apart the Motor and Impeller; discard old Impeller. Gently and thoroughly clean the internal surface of Housing Assembly seal with a toothbrush and soapy water. Carefully reassemble in the reverse order using the new Impeller. (Prophylactically, I also replaced the Motor "O" Ring and Pump Gasket.) DW works perfectly; no leaks!
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
6 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pulled drawer out and broke support unretracted support arm.
The repair was EASY! Took bottom drawer out. Used tool to remove 3 screws that held belly screen and washer arms together. Used needlenose plyers to unscrew long pointed center screw (plastic!) then reassmenbled! Hey BATTA BING BATTA BOOM!
the spray arm is held in by a plastic bracket that snaps on or off over two points. I was able to remove the bracket without using any tools,just my fingertips. It is really simple!
Neither the Soap or Wax dispensors worked for years and there was water leaking from the front of the machine.
Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.
I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time
The latch on our dishwasher broke, meaning we could not close the door or start the dishwasher.
We have a nine year old Maytag dishwasher. The handle latch is plastic and over time with the many repeated uses it cracked and broke. I went to the local appliance repair shop and found the part in their data base but it would take ten days to get and cost $22. My wife and I thought it might be time to get a new dishwasher but after checking out prices at $500 or more, I decided to search on line and repair it myself. I found the part easily and quickly on Partselect.com and it was actually half the price of another internet dealer. The photographs helped me confirm I was buying the right part. It cost $6 plus shipping and I was amazed that it arrived in two days to California. It was easy to install, simply by removing the interior panel and slipping the new piece into place in the handle. The dishwasher works like new. Thank you, Partselect.com for a quick answer to our problem!
First I had to unhook the electric, water line and drain hose. Then slide out the dishwasher. Took several days to find the drain hose - local stores only carried a 6 ft hose and I needed a 7 ft. Once I found it online, purchased it and recieved it I put it all back together and all is good.
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.
Unscrewed old nut, inserted new nut into new spray arm and screwed the assembly back in. Took less than one minute. Requested the 3-5 day delivery and received parts on second day. After examining the old and new parts it appeared the nut was the only part I would have needed, but since parts were less than $5 each I did not want to take a chance. Total cost was $16, the shipping being the most expensive item but much cheaper than paying for a service call.