CDC610B Crosley Dishwasher - Instructions

I took the bottom rack out of the dishwasher. I then took the filter guard and bottom spray arm out. Then I took the screws out of the filter guard to get to the rinse arm. I took the filter guard off, took the old rinse arm out and put in the new one. Have to make sure it is completely resting inside there. Then I put the filter guard back on. Put the screws back into the filter guard, put the two arm seals down around the rinse arm, put the bottom arm spray with guard back into the notches, put the screw top on so it can screw back in and the dishwasher is ready to go. Just make sure that you don't have a lot of soap built up, it will not clean the dishes right nor will the spray arms move. I had to call my appliance person out, and I have so much built up from soap, that I had to order a new filter guard and top and bottom spray jets. I now know to switch back to powder or liquid soap, because the tablets make a huge built up of soap... I have these parts on order now. In the meantime, I am cleaning out the jets with dishwasher magic and vinegar while I am waiting for my new parts. I now know how to put things back together so when I have this happen again I will know how to do it to save me the 63.00 office call and parts. I am happy that I know where to get my parts when I need them or break them by accident on trying to put my dishwasher back together again. Thanks.

Remove the Palnut Screw from bottom of Float assembly using pliers, Remove Pivot pin from Actuator lever w/ screw driver. Replace the Float , install new palnut Screw and re-install pivot pin on actuator lever.

That's it !!!!!!!!!!!!!!!!

Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.

So I decided to stick in some CLR to see if it would clean it up. Well it got considerably worse. So ordered the new faucet adapter, threaded adapter and the two washers, due to not knowing what i would need. It came like unbelievably fast considering it was Christmas time. Unscrewed the old one from the faucet, screwed on the new one. hooked up the dishwasher, watched it for a bit for any leaks at the connection, and it worked great! I seem to have more water pressure too coming from the sink faucet. Thank you so much for the quickness in sending out my order! -- Scott

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

It takes about 5 min. to disassembled the lower jet system. As you disassemble, make sure you clean all the filters, and asses the integrity of the filters. If they are broken, you need to replace. Once you get to the impeller, you know it is broken because the lower part is loose. To replace you need to firmly hold the impeller as you unscrew the top screw. If the housing gasket is broken or too loose, replace. Otherwise you will have leak. Refer to your models diagram for proper assembly.

I reviewed the choices available, found what I needed, ordered it, got it (quickly), and dropped it into the dishwasher....happy happy!

the spray arm is held in by a plastic bracket that snaps on or off over two points. I was able to remove the bracket without using any tools,just my fingertips. It is really simple!

Front Door Panel was replaced by unscrewing 3 screws on each left and right side of the dishwasher.

The bottom screws did not need to be completely unscrewed, just losen it enough to be able to remove the panel out.

Replace it with the new panel and screw back in the screws.

Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.

I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time

We ordered the replacement part for our Maytag model and when it came we saw that it was different than the original part. The original part had 8 wheels with a higher left hand side. The replacement part had only 6 wheels and no higher side. The replacement part would not pull in and out evenly and was a bit too narrower. We called Parts Select and told them our problem and they are going to refund us in full and take back the part they sent. Alas we will have to buy a new dishwasher. We would use Part Select in the future for replacement parts.
Alice
Cambridge, MA

First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.

First I got a heavey towel out and laid it down on the floor. Then put the protable dishwasher on its back side to expose the casters. I removed the two screws on the bottom kick plate. I cut the tops off the old casters, the plastic portion. Pulled the old casters out with pliers, then pushed the old plastic housings out using the back side of the side cutters. Just pushed the new front casters right into place. on the back ones,Just pulled the old casters right out with the pliers. they came right out. Pushed the new ones back into place.Put the kick plate back in place. Took the old upper arm nut off. Compared the parts. put the new arm in the new nut. Screwed the new nut in place. Got it back up right, hooked it up and ran it. I am disabled with nerve damage to my arms and hands. The average person could have done this in about 10 mins. It is just like it is brand new now. Jack

I replaced the old basket with the new one. Fit perfectly, now I do not have silverware falling through the cracks!

slid the part in the groove (left side)