C2S985SET2SS General Electric Range - Instructions

Very easy to install save several dollars

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

Replaced burner. New burner now ignites properly.

Slide new, better quality knobs into place.

plug in thermistor when needed

Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wall easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.

The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

I had to remove the back panel on the stove to free up taped wires to get more length.