C222 Jenn-Air Cooktop - Instructions

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Turned off 50 amp breaker. Removed knob, unscrewed holding nut and unplugged each of five wires from broken switch and connected wires to new switch.

I removed the protective grid over the filter and fan, turned the clip that held the filter in place and removed it. I placed the new intact filter for my antiquated Jenn-aire in its place, replaced the protective grid, and am happily continuing to cook on my functional cook top.Thank you.

Simply pulled the old filter out and put the new filter in.

This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,

I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.

Pulled off the knobs,replaced switch, put on the new knobs. Your web site is easy to use, and your parts are first quality. Dave

took new element out of box, inserted it into stovetop, everything was over in about 2 minutes. It worked just fine.

Turn off circuit breaker to cooktop. Remove 2 screws that hold switch plate assembly.Remove tinnerman nut from old switch using adjustable wrench. Remove one wire at time from old switch to same location on new switch. Return shaft back through hole and replace nut, be careful to not overtighten. Replace control know, turn circuit breaker back on and test. Works like new. Neil

The grease filter was 20+ yrs old and the mesh was falling of the frame. I was very pleased to find this replacement filter (the first filter I received was damaged....placed a call to PartSelect and have a new one the next day). Can't beat service like that!! Thank you, June Patten

Wife installed them, they just snap into place on the Rock Grate.

I switched the circuit breaker off at the electrical panel, removed the burner switch assembly (two screws) from the cook top. The burner switches are held in place by a single nut over the control stem. I unscrewed the nut from the failed switch, disconnected the four electrical leads (one by one) from the old switch and connected them in the same position on the new switch and replaced the nut. The clips on the electrical leads were oxidized/tarnished so I cleaned them with emery cloth to assure good contact with the posts on the switch. Replaced the burner switch assembly in the cook top, energized the circuit and the burner works perfectly again.

Loosen two screws to remove door. Removed outside trim and other outside screws hold center panel in place. Removed one screw holding hinge in place. Screwed new hinge in place. Re-attached center panel to outside trim and hung door. Easy enough.

We watched the video demo & followed it step by step. The project took about 35 minutes and we replaced the hinge on each side of the oven. First we removed the oven from the wall, then dismantled it & cleaned it thoroughly, removed the old hinges and replaced with new ones. the only problem we had was that the pin holding the hinge open was missing on one of the hinges, but we cut a nail and inserted it to hold the hinge open. The job was completed quickly, and the oven door fits and works well. Thanks for the video--it really helped us.