All Installation Instructions for Jenn-Air Cooktop C206B-C

burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.

dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.

Parts Used:

Range Burner Cartridge Terminal Block

Cartridge Male Contact Spade

Ge from Solon, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

The 6in burner would go to max heat regardless of the setting.

Un screwed the two screws in the downdraft section enough to release the unit that holds the surface burner controls.Then removed the control nob, unscrewed the two screws that holds the switch in the unit, removed the wires, making sure the color of the wires were placed on the same contact point. Put it back together and it worked
fine.Of course I did shut off the power before starting any of the above

Parts Used:

Surface Burner Switch - 240V

James from Dunnellon, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

burner receptacle failed (stove over 30 years old)

Took out burner (pulls out) Took out one screw that holds recep. in, cut the two old wires and attached new wires with wire nuts included in the new package.

Parts Used:

Surface Burner Receptacle Kit

BETH from COUNCE, TN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

replacing faulty fan switch

Disable cicuit! remove 2 screws on control housing, lift housing. Remove retaining washers from mounting posts (a trifle difficult, but drill into them with an 1/8" bit...they'll break off enough to grab with needlenose pliers). Mount & wire new switch. The replacement retaining washers are too small...hold them in visegrips & ream the hole with a larger drill bit. Place washer in a magnetic hex drive bit, align over post & tap with hammer to start them, then use a small socket to tap them home. Screw down control housing. Enable circuit...voila!

Parts Used:

Fan Switch Kit

Laird from Morrisville, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

switch became in-operative

Easily removed the housing - difficult part was removing old fasteners from posts - took 20 minutes caerfully using knive, needle nose pliers, screw driver. Used old fasteners - new ones provided were too small for posts.

Parts Used:

Fan Switch Kit

Thomas from Sterling, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

worn out burner switch

easy enough. Before you start, draw a picture of where the wires go on the old switch ( or take a picture).

Parts Used:

Surface Burner Switch - 240V

William from ARCADIA, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Jennair cooktop with coils lost one of its coil guides.

We bought the replacement Ceramic plug and wires, and opened up the jennair cooktop piece and rewired the NEW coil guide into the system. It works great.

Parts Used:

Surface Burner Receptacle Kit

Bruce from SOUTHBURY, CT
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Door hinge

My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.

Parts Used:

Door Hinge

Mr. Mike F from SAN ANTONIO, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Burner plugs were loose

used the supplied parts...very easy. The parts were exact replacements.

Parts Used:

Surface Burner Receptacle Kit

James from CONCORD, NC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken Surface Burner control

Remove 4 screws that holds down panel;removed dial;removed screw that held switch to panel. Took off wire one at a time ann put on corresponding lug. Repeated above in reverse.

Parts Used:

Surface Burner Switch - 240V

Thomas from Batavia, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burner control stopped functioning.

Replaced the control.

Parts Used:

Surface Burner Switch - 240V

Kenneth from GAITHERSBURG, MD
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Switch held on by crimp on washers.

Broke both crimp on washers. Drilled two appropriate holes in a dowell rod, used these holes to hold the new crimp on washers. Then drove the washers onto the switch's built in pegs.

Parts Used:

Fan Switch Kit

Bob from Heflin, LA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

burned burner control out of warranty

switch power supply off at breaker panel

unscrew control box assembly from stove

slide control out of stove

unscrew burner control out of assembly

transfer wiring from old control to new in same relative location

reassemble in reverse order

restore power

test burner in all positions

Parts Used:

Surface Burner Switch - 240V