BVLR333GT0WW Dryer - Instructions

replaced the two coils, which took about 10 minutes

Removed front panel unscrewed the 2 screws on the coil cover. The coil with two prongs had to upside down 3 the prong coil right side up that only way the cove will fit, plug them in re attach the cover and your done

Parts came as ordered and in really good time. The valves were very easy to install, just a matter of removing lower housing and the two screws holding in the old valves. The plug and play, no calibration needed and the dryer works like new. Very easy fix and the instructional videos were very helpful. Saved a lot of money doing it myself.

Removed 2 screws at the lint filter, unplugged dryer, next I popped the top off with a standard screw driver lifted the top all the way up and secured it from falling back down, used a 5/16" nut driver to remove the top 2 screws holding the face on, disconnected the door switch, pulled the face panel off and set it aside, then I removed the tension pulley on the bottom and took the drum out, unscrewed 2 screws holding the coils removed the old coils and installed the new reconnected the leads to them, vacuumed out the cabinet and motor, inspected all moving parts for wear, including the belt, reinstalled every thing in reverse order, had job complete and ready for clothes in 9 mins, it helps to have your son/daughter hold the drum against the back wall while reconnecting the tensioner and belt.

First, unplug power. The coils are easily accessible from the front of the dryer. Use a 5/16 nutdriver to remove two screws at the bottom of the bottom panel and lift the bottom edge of panel toward you. Pops right out. The assembly with the coils is on the front left. Use a small phillips to remove the coil-retaining bracket. Keep track of orientation of which coil goes where. Slide the suspect coil up off the column and slide the replacement in its place. Carefully slip off wire clips from old to new coil. Repeat for second coil. Reassemble and test.

The hard part of the repair was the diagnosis. I'd take the front off the dryer, start it up, and the flame would fire up. I'd put it all together, start it, hear the flame start, leave, and it would still be running 4 hours later with the clothes wet. Discovered that one of the gas valve coils would work cool and show connectivity, but would stop working shortly after starting. To check the flame and remove the front, remove the door - 1 phillips screw in each hinge, then jiggle up and down pulling away from the dryer. Then, two screws on the opposite side. Facing the opening, grasp front and pull toward you to swing it down. You can temporarily put the door back with the front off while you start it to watch the flame cycle. On regular heat, the flame will run pretty much continuously - in my case, it would start, run for about 1 minute then stop. I assumed it was cycling, but it really runs longer than that. Coil replacement was easy - unplug the dryer, pry off the electrical connectors, remove the two screws on the left which hold the retainer containing the coils Then pull the coils straight up and replace with new ones. The one with three connectors is in front; the one with two connectors in the back. There are plastic tabs on the coils which fit into holes on the retainer. Reassemble in reverse order. To confirm diagnosis, you can use an ohmmeter to check continuity of the coils. The front coil has continuity between the center connector and each of the side connectors. The back coil has continuity between the two connectors. If you're not getting a reading at 1k ohms, it's probably an open coil and needs replacement.

Removed the two screws fromt he lint track on the top of the dryer. Inserted putty knife between the top of the fromt panel and the dryer top and pushed in to release the two catches for the front panel. I rested the top panel against the wall to get it out of the way of the front panel . Next I removed the two nuts at the top of the front panel . Removed the electrical safety connector for the door using a very small screwdriver to release the catch. Pull up on the front panel to detach it from the bottom catches. I rested the drum on a couple of 2x4s to support it while the front panel was off. Locate the housing for the coils which is on the front of the dryer left side. Remove the cover fromt he coil housing by using a stubby phillips screwdriver and remove the top two screws. Remove the wiring connectors from each of the coils. Replace the coils being careful to align the coils with the "keys" in the housing cover. Reverse the process to complete the job taking care to ensure the felt around the drum does not bind.

Checked the resistor to confirm it was good. Removed the two screws that are accessible after you pull the lint screen out. Use puddy knife to release the two plastic clips that hold the top on. The top will pop up like car hood. You have to pull up on it with steady pressure. I used a plastic puddy knife to prevent scratching anything. Prop top up so it does not fall back down and strike your head or fingers. On each side inside the housing there is a sheet metal screw that holds the front of the dryer on. Before you remove them unplug the door switch wire. As you get these off you will notice that the whole front is loose and the drum looks like it will fall out. It may if you mess with it. Gently tip the front away from the dryer housing and drum assembly. After the front is out about 5 inches pull up and the bottom can be moved away out of the small hook clips. Set it aside. The burner assembly is on the lower left. The coils are there remove the sheet metal screws and lift it up. Remove them one at a time. Notice the small locate pin and position the coil in the same orientation assemble in reverse. The door is tricky to get back on. Don't forget to unplug before doing any work. This can be done without disconnecting the gas service.

Unplug electric, open top, take off front, with a small Phillips screw driver remove two screws securing the coils, remove one coil at a time, unplug and replace with new coil, secure with metal bracket and reinstall front and top and your done.

The dual cil gas valves were out of resistance range. The new coils were easy to install with a screw driver, sockets set and multi-meter.I checked the coil resistance and one of the new coils were a little high, but I installed them and they have been working fine.

I went onto the Part Select website, they have a problem solving section that told me the most likely part to replace first and a description of the machine and the location of the part. I purchased the part, I unplugged the electric cord first. I then opened up the front of the machine with a philips screw driver, changed the part with the philips scew driver, I put back the front of the machine and the machine worked. It doesn't get any better then that!

Opened the top, removed the front panel. Supported the drum with my foot while I replaced the coils. I used a very short screwdriver so I would not have to remove the drum.

Unplug appliance from power source. Started by simply using screwdriver or steel putty knife to snap up the top corners of the top section of the dryer. It swings open like the hood of a auto. Looked on the back side of the front panel and found small 5/16" bolts on either side. Removed these bolts and lifted up on the front panel to remove the panel. Slide panel out of the way far enough to access the coil kit on the lower front section of the dryer. (The wires going to the door control switch will allow this without unplugging.) May need a helper to hold the dryer drum up out of the way or prop it up as I did with a block of wood so you can easily unplug/re attach the coil wiring. There are two Phillips head screws that hold the coil keeper in place. Remove these two screws, unplug the two coils (front coil has a three connector plug and the one behind it has a two wore plug). the front coil has a small sleeve that I needed to transfer to the new coil in front. Inserted sleeve as it came out of the old coil, slid both coils back in place, replaced coil retainer being careful to line tabs on top of coils so that they lined up in the coil keeper. Replaced screws in coil keeper. Placed front panel back on being careful not to damage the felt liner that the drum spins on. Replaced the two bolts on the inner side of each corner of the front panel. Lowered the top panel and firmly pushed it back down so that the holders went in place. Plugged it up and it worked perfectly.

Need a short handled phillips screwdriver. Unplug dryer from socket. Remove two screws near the bottom of the front panel. Swing the panel to one side so electrical wire doesn't need disconnection. Remove two screws holding bracket over the two coils. Unplug both coils. Plug in new coils. Replace bracket. Replace front panel. Plug machine back into electrical socket. Problem solved.

I got great advice and the know how form other's instructions. It was a really easy fix. I unplugged the dryer and turned off the gas valve. Open up the dryer by taking out the two screws securing the lint screen. Then pop off the top of the dryer by inserting a screwdriver. Disconnect the door switch and depending on model remove the two screws or bolts that keep the front panel attached. Careful, on my dryer once took the front panel off the drum fell forward. I kept it in place by wedging a small cardboard box under it. Unplug the two wires going into each of the coils. Remember which one goes where(2 prong vs 3 prong). Undue the two screws holding the bracket to the coils and remove bracket and bad coils. Put the new coils in, attach wires and bracket. Put dryer back together. Make sure to remember to plug back in door switch. I forgot and when I tried to test it wouldn't work and it got me worried that I broke it or something.