BVLR333GT0WW Dryer - Instructions

Gas valve coils need replacing I followed parts select.com video on YouTube and had no problem. It went exactly as the video followed parts select.com video on YouTube and had no problem. It went exactly as the videos showed!

First I unpluged the dryer,thenI removed the front of the dryer,spun it out of the way but did not detach the door wires.I then took the two skrews out of the braket that held the old coils,unpluged both coils, I replaced both as I did not have the means to find which one was bad.Besides, I did not want to visit the insides of the dryer for another five years. This was a snap and the parts were perfect and arrived timely.

When you open the door to the dryer there are 4 screws you need to remove (2 on each side) in order to remove the front panel. Once I removed the front panel I then turned the dryer on to see what was happening inside. The heating element was turning orange with a glow but the gas wasn't igniting. After looking on-line I figured my next option would be to replace both gas valve coils (one is 2 terminal & the other is 3 terminal). Once you have the new parts & are ready to install them unplug the dryer. All you need to do is first, unplug the 2 plastic sockets that feed the electricity to the coils (they have wires attached to them) unscrew the bracket that holds the 2 coils in place, pull the old coils out & put the new coils in, replug the electric plugs, re-attach the bracket that holds the coils into place, plug in the dryer & turn it on. Test it without the panel on so that you can see that the gas ignites. My husband was very happy when I told him I repaired the dryer - beats paying another repair man.

bought the new coil valves changed out new for old, presto dryer works now

This 10 year old dryer stopped heating. I knew a Maytag would have much more life left in it than that (even my Mom's lowly GE lasted more than 40 years!) so I was sure it could be fixed. Without doing any testing, I had just guessed that the glow bar was bad and replaced it. But that wasn't the problem - the old glow bar still had continuity as tested with my ohmmeter. So I dug in deeper and looked over the schematic posted on PartSelect's website. The glow bar would light up and then go out, but the gas valve never opened. After probing the two solenoid coils for voltage, I decided the primary solenoid was bad. This was confirmed when I took the connector off and checked with an ohmmeter (never do this with the wires connected!) and found no connection at all between the two terminals.
Ordering the new part from PartSelect was fast and easy and my part arrived in two days. The solenoid coil on this dryer can be removed from the gas valve without taking any gas lines apart - I don't know if they're all like that, but it's a great feature. The only hard thing is that there is no access door to inspect the flame like older gas dryers. You have to take the front panel off to watch it working, but that just involves the four screws around the door opening.
If your pre-Whirlpool Maytag dryer is giving you trouble, take heart! These are great machines that last long, are easy to fix, and parts are easier than ever to get with PartSelect!

and the problem wsa solve

it was easy, it clip right on.needed to give it a little tap to get it in .

took off bottom access panel replaced both electronic coils web site helped diagnose problem

well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work. Thanks a lot. so if no flame, must be the valves...

Replaceing only this item fixed my problem
with front panel removed Ignier would turn on, gas would light, ignitor went out as usual, but gas would shut off after a few minutes and not come back on.
Note gas dryers are supposed to light, heat up, igniter stop flame stop after it gets up to temp, shut off for a while then repeat the process, it would have saved a lot of time researching to have known that earlier.. Take front panel off screws off, take panel off holding the 2 round coils in place, unplug the one with 3 prongs and replace, tested dryer with the panel off and the door closed so there was no suction issue. put panel back on 5 minute fix if you knew what you were doing.

Removed Two screws took out the coils put in the new ones
I ordered one day and got them the next day. Thank you partSelect For the quick service.

Unplugged dryer, and removed vent hose. Tilted dryer back, unscrewed 2 screws on lower front panel. Removed 2 screws on coil holder (needed a short screwdriver). Unhooked wiring harnesses from coils, and removed coils. everything in reverse for installation.

I replaced the dryer coils in 5 minutes!!!! It was so easy! If I called a repair guy, he would have charged me $200. I fixed the problem in 5 minutes, and all it cost me was the price of the coils...$15. Sweet!!! I upgraded the shipping to 2-3day, and the coils arrived the NEXT day. Great experience, and very satisfying to fix my own dryer. The dryer works perfectly now and gets very hot!

I saw some videos to have an idea on Wat to look for,most of them described the sensors and the igniter, but one specific mentioned the coils. I did the testing and because all the components were fine I concluded that the coils was the problem. Went online ordered the parts, 2 days later got them, took of the old ones installed the new ones and the job was done drying perfectly. It cost me only $ 25 bucks and probably 10 or 15 minutes to fix it. Tanks part select You have an excellent service.

super easy 2 screws and my 11 year old son took 5 minutes.