BEC316ES1 Crosley Range - Instructions

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

The replacement of this part is simple enough, out with the old, in with the new. At issue here is the way the controller fails. The heating element goes to the highest temperature. The original controller on this Kenmore oven failed after about two years and the first replacement that I got from you lasted about a year and a half. The defective controllers seem to be working properly once the controller has been turned off and then restarted, but the frequency of failure increases with time until you hardly dare to step away from the oven. This controller should open on failyor, not close.

George Ritz

Broil worked on the stove, however in bake mode, the oven did not make temperature. Turned off the stove, unscrewed and inspected coil. I noted there was a section of the coil that had a "corroded" appearance. (it was evidence of the coil being burned out). Checked with a ($9.00) voltmeter, showed infinite resistance. Found the original envelop for the stove taped to the back of the oven from 1973. It has wiring diagram with schematic and noted the coil was 3000 W, 19 ohms.

Bottom Line found comparable replacement online and tested resistance, measure dimensions of the old coil, matched with Watt rating, replaced, tested installed and works great, Oven has been in use for a couple weeks now. New stove would have been around $500.00. Not to mention some remodel work, as the house is old and stove is a built in.

Coil was $60.00 and should buy the time I need until I remodel the entire kitchen.

bought drip bowl from big box store and the 8 inch did not fit . yours fit perfect will use you for future diy jobs thank you

Took out the bad element and replaced it with the new element in less than 5 minutes, worked perfect, thanks

I just pulled the old ones out of the sockets, cleaned underneath, and replaced with new ones. No-brainer.

searched on the computer for the name and part number that was damaged, found that it was the bake element so i ordered it with part select.com. when it arriver three days later (as expected) i disconnected the gas and electric to the range and simply removed the old element with a phillips screw driver. installed the new element, hooked the gas and electric back up and began cooking again...

thanks partselect..

I started to smell burning electrical smell from the burner area and heard a "buzzing" sound from the burner control while the burner was on. Pulled the element and noticed that the wire coil end of the left element was burned and pitted from arcing.
Pulled the range top up, used a phillips screwdriver to remove the terminal block clip from the range top. Upon inspecting the burner terminal block, I saw the brass wiper was missing from one side of the left slot, and there was considerable heat damage around the slot opening.
The terminal block being replaced was already replaced earlier for the same problem. The appliance repair folks recommended that we use light cookware on the burner. Instead, ensure both element leads are fully inserted into the terminal block.
I turned the power off at the breaker, used a utility knife to carefully slit the heat shrink tubing on the existing replacement, unscrewed the ceramic wirenuts, removed the old block, straightened out the range wires, slid the new heatshrink over the range wires, then twisted the new terminal block wires to the range wires. Screwed on the ceramic wirenuts, slid the heatshrink tubing over the wirenuts, and used matches to shrink it tight.
The package contains an instruction sheet with simple instructions.
Once the new terminal block was installed and the element terminals were fully seated, the "buzzing" from the burner control disappeared.

Generally straight forward repair with the most difficulty coming from the screws holding the element in place being rusted. Took some wd40 and some snub-nosed pliers to get them out. The wire connections on the back of the element are pretty self explanatory. Lightbulb was an easy change though the bulb connection had also rusted a bit and required some pliers to remove.

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Extremely easy. Two screws and electric connection that had easy pop on-off connection.

Unplug the oven (very important). Unscrew the bad element and screw in the new one. Plug oven back in.