Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ATF6000FS1 > Instructions

ATF6000FS1 Frigidaire Washer - Instructions

All installation instructions for ATF6000FS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6000FS1
121-135 of 291
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken shock

  • Customer: Scott from Pearland, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 1 people found this instruction helpful
My washer was leaking a bit on the left side, apparently from the place water enters from filler. I spent a bit of time inspecting that side of the thing and my jaw dropped when I finally saw the other side of the washer, the upper shock was broken off and the thing was not connected.

I got my parts fast and removing the pins was a bit troublesome but some from access standpoint, but it wasn't hard - just took some extra effort and prying from the head side. Seems to run better with new shocks and no more leaking so far.

broken shock absorbers (were all plastic)

  • Customer: Patrick D from Port Orchard, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
It took more time to remove the screws on the back panel..
remove back panel for better access..
remove speed access box on lower left side ( 2 screws) to get access to nylon pegs, squeeze down on tabs and pull out . the little tabs are on the oppsite side of the split nylon...
Replace shocks and nylon pegs..
reattach speed access box.
put the back on.....
easy job, the new shocks are part metal, make sure the metal side of shocks go towards the tub...

both left and right shock absorbers had broken into they are plastic on my front load galeriey series washer

  • Customer: Les from Belleview, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the bottom front panel ( 2 screws) and about 8- 10 inches back were the shock absorbers...the one on the left was easiest nothing in way I squeezed the locking tab and pushed the pin thru to remove the shock absorber...on the right side was a little tricky but got my arm round the drain hose and small pump and pushed that pin thru as well...installed new shocks and was good to go...I did call a local repair business here in belleview florida was told the shocks themselves would cost 37.00 for the pair and about 150 - 175 in labor...I paid 22.00 from parts select and did my own labor thanks for all the help...les

Broken shock - slight leak

  • Customer: Duffy from Wheaton, IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
You could do the replacement by just removing the maintenance panel on the front, but removing the rear panel gives you more options for getting at the shocks.

The front panel comes off with 2 screws, the back has a lot of screws holding it on, a cordless drill is the way to go.

Prying on the head of the plastic bolt with a pair of needle-nosed pliers while pushing down on the tab seemed to work well. I did have to remove a small box that houses electronics to remove the one from the right side.

While I was in there, I tightened up the numerous bolts that holds the drum shell together. Machine is much smoother now and no leaks.

Bouncing and noisy washer

  • Customer: Chad Trainum from Albuquerque, NM
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I had read the instructions and suggestions on the site. The product arrived with a good set of instructions. I used the deep socket to push in the "catch" on the pins. Once the catch is depressed I pulled and twisted a bit to get the pins out. After I pulled both broken shocks out I replaced them as instructed. I did use a long wooden dowel to get the pins all the way in. Read the instructions and follow what they tell you and it'll be done in under 15 min.

knocking noise when washer changed directions

  • Customer: Randy from Okeechobee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
First I removed two screws in front lower panel to access lower portion of washer machine. Use pilars to push four plastic pins from each end of two vibration/shock abs. Job was very easy and took less than 30 minutes to complete.

one broken shock

  • Customer: Joseph from Steger, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
when I replaced the other one it was broken also but you wouldn't know it by just looking at it. The only problem being able to get the new one back on I put it on pushing from the front, I can only imagine the ttrouble I'll have get it out again I'll probable have to cut it out with somthing because it's right up against the circiut board housing. other wise not a bad job. But I think my age has somthing to do with it.Not much strength.

one of shock absorbers was broken

  • Customer: Fred from Russell, KS
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
I followed the instructions that came with the parts. I used a regular socket to remove the pins instead of the deep well socket recommended, because I didn't take the machine completely apart. and the space wasn't enough for the deep well sockets. It worked perfectly. After I got the pins removed, then oriented the absorbers correctly and pushed and pulled the pins back in place and it was done.

would no longer spin properly

  • Customer: Paul from Pony, MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Assumed this 12 year old washer was broken beyond repair so went to Lowe's and paid $880 for a new one. Out of curiosity, I removed the back and the lower front panel from the old washer to see why it would not work and found the two shock absorbers were both broken. I ordered new ones and it took me 15 minutes with a pair of pliers and a small hammer to replace the shocks. The washer now works perfectly again and I could have saved $880! Goodwill is going to get lucky on this one!

Washer would agitate but not enter spin cycle

  • Customer: Jason from Haymarket, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Washer error code said control board($200.) but this web site said Door Lock and Switch assembly($80). Web site was correct, thankyou for saving me money and time for the real repair needed.

Shock broke

  • Customer: Robert from Coldwater, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 1 people found this instruction helpful
replaced as instructed.

Broken shock absorber on washing maching

  • Customer: Richard from Novi, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 1 people found this instruction helpful
Watched video on-online when I ordered the parts. The video showed the left side shock replacement and it looked very easy, however; the right side require a little more work due to the motors and electrical box that had to be moved before I could remove the shock pins. I layed the washing machine on its back and removed the broken shocks and put the bottom pins back in on each schock and then stood the machine back up right; took the back panel off so I could replace the upper pins on both sides with ease. I then went to the front and re-attached all the hoses, clamps, and electrical box. Before I replace the front panel, I took a 1/4 socket and wratchet and leveled the machine in its perminent place by adjusting the four feet by reaching into the machine with the 1/4 inch socket and wratchet and adjusting the feet one by one until level.

machine would not go into final spin, clothes saturated

  • Customer: david from edinboro, PA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
with the help of my nephew, we unstacked dryer after power sources were shutoff first. then simply removed the two screw attaching lid on washer. then removed two screws holding switch from front of machine. fished switch up to a visible area, exchanged bad for good. fed switch back to it's home,then reversed assembly procedures. these forums are great and have saved me money by enabling the repair both washer and dryer at a very reasonable cost without the need of a certified repair person.

broken shock absorber

  • Customer: pavel from west linn, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I open the front, bottom side and everything was in front. I took out the plastic bolt and replace the absorber.

Noise And Vibration

  • Customer: Brian from Austin, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Some parts are hard to remove due to the inability to see the locking section of the fastener pin. The parts installation is self explanitory and no asdjustment is required, so beyond laying on the floor of a very small room and not being able to see some of the parts it's not bad.
All Instructions for the ATF6000FS1
121-135 of 291