ARS635 Amana Range - Instructions

removed the screws disconnected the old one and connected the new one and put the screws back on it

I took a couple of screws out that hold the bottom
element in place replaced the old one with the new one and fired it up. Worked like a charm and maybe this old stove will live on to make more Roast beef dinners.
If it been any easier my 10 year old grandson could have done it.

First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They work very well now.

Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up stove. Restored power. Burner now functional.

Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the connectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.

my wife did the the job and it was that easy. she took out two screws sliped the wires off put the two wires back on and put the screws in . She is a bank teller and teachers water aerobics

Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I installed everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.

First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.

Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.

First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws for the cooktop.I put in the new burner & it worked just like new.

Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube over the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!

All the necessary parts came in the repair kit, delivery was timely. Very easy project.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.

While trying to clean the oven, I decided to remove the lower heating element to make it easier. After removing the 2 screws on the bracket that holds the heating element in place, I pulled the heating element out only to short it out on the back of the oven and wreck the element. Luckly I was not injured or shocked, so if you need to do this, I recommend reading the owner's manual on how to property ground out the circuit first.

Anyways, to replace it, I just removed the lower panel on the back of the oven (roughly 10 screws). Installed the new element on the inside of the oven and screwed it into place. Then, connected the wires to the element from the back of the oven. Replaced the panel and turned the power back on.

In all, it took probably 15-20 minutes to fix and only cost me $37. I know that a minimum repair cost for this from Sears would have been $150, so definitely worth my time.