ALW480DAW Amana Washer - Instructions

Removed the old hoses and screwed on the new hoses.

Unplugged washer and disconnected water lines and drain hose from wall. Removed the two Screws at bottom front panel and tilted lower portion out at bottom and removed panel. Removed screw on each side under to top panel, removed three phillps screws on top control box to tilt the top box forward and unplugged the wiring harness,unscrewed the ground wire, pulled off water level hose, disconnected switch power wire connections. Slid control forward and removed. Found broken spring and anchor slit rusted thru where spring attached to base. Cut a 1/2" strip of metal from a 2x4 metal strap and attached to bottom side of base with screws, set washer uprite and tilted top panel to attach springs to tub. Inserted spring at bottom and pulled spring into slit on side of tub with a heavy gauge bent wire, bent like the top of springs being replaced. Reconnecd wiring to to panel box & Hose, srewed in place at top, reattached screws uhder top front left and right and inserted front panel at top and attached two front screws at bottom. Reattached hoses and plugged in unit. checked for spin, o.k.

simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.

I tipped the tub towards the area where the springs were and connected them. They broke because that particulary area seemed to get moisture and they rusted. Truthfully, although the machine still works, its last days are just down the road.

this machine seems good to work on because almost every thing is done from the front without pulling it away from the wall. Removed front lower cover by removing two screws. There are three brake pads with two bolts each. applied silicone grease to each pad and put it back togather

I had to take the entire tub assembly from the machine to replace the milkstool which had been crushed by the weight of over-loading the washer. It took about 2 & 1/2 hours to complete the job, but it was well worth the effort to save the expense of replacing the appliance. Part Select provide the right part as promised and saved me a lot of money. Thank you for your service.

I used your great video for pointers as to what to do. I took off the front, raised the top, vacuumed the whole thing up, that took quite a while. Took out the drum. Did more cleaning. Then took off the old retaining rings with retaining ring pliers, took off the old drum rollers and support. Replaced with new roller supports, washer, roller, washer and retaining rings. Then I replaced the belt. Tested it and turned the wrong way and it came off. Replaced and tested it again and I don't know why but it came off. Replaced the belt again, tested fine. Then I replaced the felt pads and glides, they were worn. I ended up asking my husband to help hold the drum so I could get the front back on. Replaced front and door. Tried the dryer. Works great AND very, very little noise. Note: when taking the wiring off the light and the door switch, I took photo's of those places with my cell phone and had them to look at to make sure the wiring was correct.

Unplugged washer from power source. Dissconnect the water supply. Take off lower panel. Undo big spring. Remove 4 bolts that hold the motor. Unplug the motor. remove motor and belt. While on the bench I regreased the Idler pulley. then reverse the procedure to reassemble

MAYTAG SAV2655AWW Series 10 Washer Tub Bearing and Seal Replacement

1. Unplug washer power cord and turn off water supply to hoses.

2. Remove lower front panel, 2 5/16” hex head screws at bottom of panel.

3. Remove front upper panel, 2 5/16” hex head screws at bottom corners of panel.
4. Slide washer out from wall far enough to provide clearance to lift washer top panel and control head.

5. Remove 2 5/16” hex head screws securing washer lid panel to side panels and lift lid.

6. Pull fabric softener dispenser from agitator, pulls off easily.

7.Remove agitator upper section, pulls off easily. Remove ½” hex head retainer bolt from inside agitator.

8.Remove agitator base section, pops up, place fingers under each side and pull up gently.

9. Remove tub top ring by pushing down at each clip and then prying out lightly to disengage clip, 8 total. Orientation for reassembly is done by referencing the double tabbed clip on the right side of the outer tub.

10. Remove inner tub retainer bolts, 4, ½” hex head. Clean off mounting hub to expose 4 pry slots located exactly opposite each other. Using wide flat head screw driver carefully and evenly pry up inner tub off of aluminum mounting hub. Once tub is ¼” or more raised a wider blade pry bar will help prevent cracking or breaking the inner tub.

11. Remove plastic seal cup from transmission shaft by turning it counter clockwise with a medium to large pair of water pump pliers.

12. Remove inner tub aluminum mounting hub by using a hammer and broad flat faced punch or drift and driving the hub counterclockwise. You can be aggressive about this as kit comes with a new hub. It will loosen at some point and can be unscrewed by hand. The transmission shaft threaded section must be thoroughly cleaned to remove all sealers or debris from the threads or the new hub in the kit will not thread on correctly and will be excessively tight. Lightly place anti-seize lubricant on the threads before putting on new hub and seal cup.

13. Remove water pump hose from outer tub. Then remove second hose from water pump.

14. Remove “Fill Sensor” hose. Back left quadrant of outer tub, pulls off easily.

15. Remove 6 tub ( 3 pairs) stabilizer springs, plus 1 spring in very back. Try to watch how back one connects to tub mount. If you miss it hooking it back up is pretty straight forward. Only secures one way. Channel locks or vise grips work best for working with springs.

16. Disconnect wire harness from motor drive assembly and tub frame mount.

17. Pull tub and motor drive assembly out of washer cabinet. Lift carefully by shaft and tub mount frame.

18. Remove 6 outer tub retainer bolts and 2 upper motor frame bolts.

19. Lift tub off motor frame and set on its side carefully to prevent damage to “Fill Sensor” back left side.Use a slide tool to pop bearing assembly out of tub bottom.

20. Clean the tub, bearing mount surface, remove all grease from shaft and shaft spline sealing O-ring.

21. Wet new bearing seating surface and tub mounting surface lightly with water and press in new bearing by hand.

22. Clean both inner and outer tubs inside and out thoroughly. Clean hub mounting threads on motor shaft thoroughly.
There can be no residue of any kind in those threads or new hub will be difficult to impossible to screw on without damaging it.

23. Reverse dis-assembly procedure to reassemble machine. Recommend replacing drive belt and idler pulley if found to be excessively worn or damaged. If brake assembly is heavily worn or pads are cracked this is the time to replace those as well.

I removed three screws to gain access to the timer. It has a label which describes how to remove the contol knob but does not address the removal of the timer knob skirt. I tried prying it off but was unsuccessful. This caused the removal of the timer to be very difficult. After the skirt came off the timer was easy to remove. The timer is held in place by one screw. The new timer went in real easily.

It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks

Remove the lower access door in the front of the machine. Then I tipped the washer back against the wall to access everything. The pads are alittle hard to push in between the washer pulley disc. So I first pushed in an old broken brake pad off to the side, then was able to push in the new pads. The rear pad is the hardest and I had to release some of the front tub springs and remove the pump hose for access. Overall it went pretty smooth. Thanks for your help!Tim

I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.

Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.

Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.

No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.

1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump