AE3213 Dryer - Instructions

Well tried to find this simple part around Columbus and even maytag website no luck.Parts select had it to go and arrived earlier than expected.Fixed it less than 5 minutes works great.taken longer to put the light bulb back in,Really like the accuracy and quick response from parts select.If I had called a service tech probably would have cost $50.00 or more for a part that cost a little over $3.00 and saved this site in case I need to order other parts.Thank you

one screwdriver, one new door latch, five minutes! Pried out the female part of the door latch, tapped in the new one and started the dryer. Never had an easier repair. Usually there is some hitch along the way you learn about the hard way, but not this time. TOO EASY!!

Removed the front panel of the dryer and drum to replace the rollers. You will need a snap ring pliers to remove the locking snap ring holding the rollers, replaced rollers, installed new drum belt and replaced the front dyer panel.
Tested the dryer no more noise.

Thanks

popped out the old, broken female latch, popped in the new one in less than 30 seconds. We had been leaning stool against the dryer door for 5 years. Now it works exactly like it is supposed to.

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

The dryer door on my mom's Maytag SG1000 (washer/dryer stacked unit) wouldn't stay closed; the latch had finally broken. The replacement kit includes both the female latch and the male striker. I replaced both even though the old striker was still good. The old parts were easily pried out and removed with a small flat-blade screwdriver. But what the PartSelect website, and the other "repair stories" found here, fail to mention is that the male striker is held in place with a small metal "door strike retainer" plate that falls down into the door as soon as you pry off the striker. You will need a small Phillips screwdriver to take the door apart and retrieve the plate. After snapping the new striker into the plate the door can be reassembled -- a simple job that only takes a couple of minutes.

Removed old latch. Installed new latch. No problem.

Only needed half the parts. Installed the catch for the door and saved the other part.

Pop out with screwdriver and push in new part. easy

Popped in the new part. Really! That easy!

Took 2 screws out of the bottom of the dryer so the front face plate came off. This allowed access to the door latch catch, which was easy to pull out with pliers. Pushed in new latch catch until it "popped" into place. Easy, easy, easy!

unscrew the screws at bottom front of dryer, lift outward, upward, the bottom of the front of the dryer. As the dryer front tilts outward/upward from the bottom, the area where its hinged at the top of the front will disengage from the main frame of the dryer and the face of the front of the dryer comes off. remove the old door latch by manipulating the plastic body of the latch (wiggle, twist pinch . . .) until, from the back, you can push the old latch forward through the front of the front of the dryer. At this point, you can put the new door latch back in from the front and push it in to place.

To remove and install the new parts, I followed the video instruction at whirlpool.com. Then removed the old knobs and put the new ones in. The new one created a rough contact and needed a little lithium grease to make a smooth insertion to prevent the friction from damaging the new part. It was an easy fix and took about ten minutes. Good luck in your repairs!

A simple repair. Just a screwdriver was needed (and of course the latch parts), Took all of 5 minutes